Search results

  1. gilby959798

    What have you done to your square lately??

    I didn't do anything to mine, I'm a few hundred miles away from it but I spotted this at the Sam's club
  2. gilby959798

    What have you done to your square lately??

    Fixed the inner roof windshield lip today.
  3. gilby959798

    Tremec TR-4050 swap

    I assume it is all installed now, how do you like it?
  4. gilby959798

    What have you done to your square lately??

    Does anyone make these stickers? Mine is just too far gone, when I removed it it came apart.
  5. gilby959798

    What have you done to your square lately??

    How do you like the H2D, I have a K2 Plus because I just couldn't justify the H2D price at the time.
  6. gilby959798

    What have you done to your square lately??

    I have an MGW and a Long Tube Header resonator delete. It is a great car, we do a lot of road trips in it with my wife and kid. The kid has already claimed it as hers, maybe when she graduates.
  7. gilby959798

    What have you done to your square lately??

    What spec GT350? Here is my 16 Tech Pack... It was an unfortunate mistake buying the tech pack but I still enjoy the car.
  8. gilby959798

    Custom Fender Badges

    I have 2 sets of the original sierra 25 emblems, but I wanted something slightly different, they're side specific and much larger than the factory.
  9. gilby959798

    Custom Fender Badges

    Another one with resin on my old fenders out back And one without resin, still holding up strong but I like the way the resin looks, going to try some new resin and see what happens.
  10. gilby959798

    What have you done to your square lately??

    If it is in an oil bath, it shouldn't need grease.
  11. gilby959798

    Custom Fender Badges

    This one has been setting out in the weather just like this for 6 months, it gets full afternoon sun. The resin yellowed but it looks great other wise. I have 2 more on the old fenders out behind the shed, I will try to get pics of them at some point.
  12. gilby959798

    Custom Fender Badges

    I used PETG, I have done things both in PETG and ASA depending on the use case. How these are mounted, I have yet to see any degradation on my test pieces that are outside and in the sun not supported fully. I find that multicolor prints work better with the PETG, as I have less issues. It also...
  13. gilby959798

    What have you done to your square lately??

    That is what I did! She wasn't home. Luckily it was before I had replaced the oven.
  14. gilby959798

    What have you done to your square lately??

    I did this with headlights once... Barely came out with my rear end after the wife heard what I did
  15. gilby959798

    What have you done to your square lately??

    A miata might be the answer then haha
  16. gilby959798

    What have you done to your square lately??

    Honestly, I was thinking of it being a project for her to work on and learn some good life skills. I don't want her to have something ultra nice. I do want minimal seats and a manual. Its hell for these kids when I was them at one time :gathering:
  17. gilby959798

    Custom Fender Badges

    I actually drew it up to make this, so it might not be 100% perfect but it looks pretty close IMO.
  18. gilby959798

    What have you done to your square lately??

    I keep telling the wife that is what I am going to get our daughter for her first vehicle. Manual roundeye square 4wd shortbed.
  19. gilby959798

    What have you done to your square lately??

    This really makes me want to get a short bed 4wd to go with my 3/4 ton 4wd.
  20. gilby959798

    Tremec TR-4050 swap

    Interesting, when I asked it was just a clutch for the setup. I haven't ordered my engine yet as I am still doing metal work.
  21. gilby959798

    Tremec TR-4050 swap

    How is the swap treating you? Assuming the T case has been modified accordingly and is installed.
  22. gilby959798

    What have you done to your square lately??

    Yes! The price of entry isn't that bad either, depending on what you want. I have sold enough to cover my printer as well, once you design something that is wanted by others anyway. It does help when you can draw up your own parts though.
  23. gilby959798

    What have you done to your square lately??

    I just went out and looked at mine, since its all apart. It doesn't have a grease fitting, its a 77 built in late 76.
  24. gilby959798

    Tremec TR-4050 swap

    Following up on the install of this.
  25. gilby959798

    What have you done to your square lately??

    Started taking the roof off. The main reason for this: Found a critter home And test fit the panel.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,340
Latest member
hauto85
Top