Search results
-
Easton Definitely Has The spirit
This boy has too much free time on his hands I guess. Definitely the most festive square in the Metroplex Merry Christmas Everyone Randy and Easton- Randy and Easton
- Thread
- Replies: 0
- Forum: Exterior
-
Oh My What has Easton Bought Now
Thanks y’all…. I will keep you updated as we move forward- Randy and Easton
- Post #6
- Forum: Other Vehicles
-
Oh My What has Easton Bought Now
Well y’all, been laying rather low with just minor things popping up on E’s square. I go out of town and come home to this! He bought this 85 Burb to restore! I asked him who was going to help him, and of course he said I was. I told him we nearly killed each other during the first build...- Randy and Easton
- Thread
- Replies: 9
- Forum: Other Vehicles
-
Vintage Air - Compressor Not Turning On
Call VA directly. Great customer service! Leave a message and they will call you back Randy and E- Randy and Easton
- Post #2
- Forum: Tech Discussion
-
-
-
Dome light upgrade
We used the LED upgrade for dome and left original foot well lights original since I could not find direct replacement LED to fit those sockets. We did add a floor well LED under dash over hump and it totally illuminated the floor and just tapped the power from stock well lights. Randy and E- Randy and Easton
- Post #5
- Forum: Garage
-
fuel venting
Sorry for late response, I used charcoal for fish tanks and it has worked fine, no smell Randy and E- Randy and Easton
- Post #20
- Forum: Tech Discussion
-
fuel venting
Ken, we had same issue. PO did the charcoal canister delete 2 port sending unit as well. Found that same steel line under radiator shroud and PO cut it drivers side bottom and that was it. We smelled gas all the time and could not find at the time a canister. I made a small charcoal filter...- Randy and Easton
- Post #11
- Forum: Tech Discussion
-
Charcoal canister delete?
Perfectly! No complaints and no gas fumes smell- Randy and Easton
- Post #42
- Forum: Carb Fuel Systems
-
New owner of an 87 K10 Stepside
Well howdy neighbor! We are NRH….. enjoy the build.. Randy and E- Randy and Easton
- Post #15
- Forum: Introduction
-
New to the squarebody family
Nice rig! Welcome from DFW- Randy and Easton
- Post #12
- Forum: Introduction
-
New owner of an 87 K10 Stepside
Welcome from DFW Texas!- Randy and Easton
- Post #12
- Forum: Introduction
-
Long Time Lurker, Finally Signed up 86' C10 SWB
Welcome from DFW Texas and have fun!!!! Thanks for the pic- Randy and Easton
- Post #11
- Forum: Introduction
-
New member from North Carolina
Welcome from DFW Texas. Nice motor- Randy and Easton
- Post #21
- Forum: Introduction
-
dash pad
…adequately titled my friend!!best of luck with that! Hahah- Randy and Easton
- Post #5
- Forum: Interior
-
Trash my dash? And interior panel take offs?
Lesson we learned in our build is you never throw anything away. Either you needed it later for a template, or someone else needed it or you can’t figure how the new stuff goes in and you have something to work with…..I can’t tell you how many times we needed something we had discarded months...- Randy and Easton
- Post #3
- Forum: Interior
-
Loose cab mount
We were very lucky on our cab mounts. We had read and saw some people on YouTube that had such trouble with them so we were prepared. We set aside an entire two days for just the mounts. Easton got the first one done in 20 minutes, and had them all finished before lunch the same day. We were...- Randy and Easton
- Post #6
- Forum: Exterior
-
-
Opinions on grounds needed
@RustyPile will be along shortly with some great advice but here is a great list. Randy and E- Randy and Easton
- Post #7
- Forum: Electrical & Audio
-
Alternator cable routing
That is awesome! Randy and E- Randy and Easton
- Post #10
- Forum: Tech Discussion
-
Belt squeal (while accelerating)/alternator question
We are with @Snoots and @Buck69 bigger belt. Here is a pic of E’s setup. Got belts on Amazon which has a Goodyear belt section with free shipping and returns. Due to our custom set up, we ordered several different sizes and sent back the ones we did not use. Very convienient Randy and E- Randy and Easton
- Post #10
- Forum: Tech Discussion
-
Remove accessories from this old truck?
We are a leave it!!- Randy and Easton
- Post #6
- Forum: Aftermarket Accessories
-
Easton Is Graduating Thank You all for your help GMSB!!
#grateful Randy and Easton- Randy and Easton
- Post #32
- Forum: Introduction
-
Vent window adjustment?
Lots of soapy water, or window cleaner and use a plastic tool to push it into the frame. The precision gasket came with a plastic tool that worked well. We found if you heated the gasket with heat gun or hot water (we did ours in December and it was cold in garage) they became more playable...- Randy and Easton
- Post #15
- Forum: Tech Discussion
