Search results

  1. Goldie Driver

    Done dun it

    Well, all you will need is a block off plate and a gasket and to plug the 1 vacuum hose that feeds it. Id say try it and see if your gas milage :p is affected or drivability after just fooling with that component. *Edit* Did not read your post correctly in that the other smog stuff is off...
  2. Goldie Driver

    All time 4x4 / NP203 Truck Questions, hard to make tight turns

    My 1st instinct would be to see if it is in Loc as that will cause it to fight on turns. Both ways, however, not just right. Just get the transfer case lever in Neutral and pull it back 1 notch - that will be regular 4 Hi, not 4 Loc. Got pics of the 77 ? :)
  3. Goldie Driver

    What have you done to your square lately??

    Oh, I wish ! :p That is where the cable for the shift indicator connects to the trolley. The cable came loose yesterday and during my reattach attempt that happened. Thanks to the aftermarket DIN radio that is mounted to the bezel :321:by the PO or whomever dash work sucks. I guess it...
  4. Goldie Driver

    What have you done to your square lately??

    Well, more what I will be doing ... again. Know what this is?
  5. Goldie Driver

    Non-stop horn honking

    Have any pictures of the install ? The horn is constant power but only works when the circuit is ground by the horn pad. With *only* the lock plate and cancelling cam installed I cannot mentally picture what could be causing that unless the turn signal switch went bad randomly or the relay...
  6. Goldie Driver

    Intro and oil pressure gauge question

    Welcome from Houston! Being a 6 cylinder I can't offer a lot of info , but it is a free bump ! Britt
  7. Goldie Driver

    77 K-10 Silverado Suburban in Tuxedo Black

    What a find , and welcome from a fellow Sub owner in Houston! Got interior pics? :cool:
  8. Goldie Driver

    Hood Decal - Any leads

    Not quite sure what you are after, but this might be cool ! https://phoenixgraphix.com/gm/1980pcih.php
  9. Goldie Driver

    smog equip. any value/interest ?

    I'd suspect there will be a need for it from some member unlucky enough to be in an emissions **** area ... ( Edit - LOL N a z ! was flagged ) Free bump for whomever that may be, and a thank you for being willing to help someone out !! :patriot::waytogo:
  10. Goldie Driver

    Dash turn signals not working

    Are you certain the bulb holders are making good contact with the printed circuit board ? I have had issues with that with Goldie - the plastic of the cluster is old and they do not hold as tight to the board as they would have new.
  11. Goldie Driver

    Dash pictures of ‘77 K5 Blazet w/tach

    According to the RamCharger FSM's ( 73 thru 80 body style ) only a small portion of current was shunted thru the ammeter. Yet, if disconnected, they would not run ... HMMMM. Mopar wiring in the old days was never known to be the best !
  12. Goldie Driver

    Wiper Pulse Module #15598496

    Pardon my lack of French :Big Laugh:, but what is a SCR ?:think:
  13. Goldie Driver

    Tire size or possible lift recommendations for the 79’ K30

    My 60 year old opinion :rofl: is it has a good stance now and adding a lift will be dollars, labor, and possibly driveshaft issues for little gain and potentially more difficulty climbing in. I'd vote to keep it as is.
  14. Goldie Driver

    Fusible link?

    Yeah, I mean you are right ... :cool:
  15. Goldie Driver

    Hi from Julian,CA

    Welcome from Houston, Texas, and good job on the pics ! :waytogo:
  16. Goldie Driver

    Hi from Denmark

    Welcome from Houston, Texas! Nice find with only 43K miles :waytogo:
  17. Goldie Driver

    What have you done to your square lately??

    I honestly thought they were farther worn than that, especially from the noise ! :rofl: Oh, well- I am planning on taking Goldie for a road trip to the National Forest with some high school buds next week and new tires seemed like a good plan.
  18. Goldie Driver

    What have you done to your square lately??

    Keeping Discount in business! The 2 fronts with around 4.5K to the back and 2 new fronts. Uneven wear for sure ...
  19. Goldie Driver

    Odd cable/control going to foot feed.

    I suspect since the PTO has to be run in neutral and the lift requires the PTO driven pump so the line lock is an additional failsafe to prevent movement. Sounds good - may even be accurate. :waytogo:
  20. Goldie Driver

    Part Choice-Brake System

    Where are they made ? China and Brazil, surprisingly, are on my No No list unless there is no other choice. Based on No other info other than what you gave above Rochester NOS hands down.
  21. Goldie Driver

    Afflicted Squarebody Head Hello to Everyone

    Welcome from Houston! 11 MPG on what I am picturing as a full time 4wd is actually amazing. :cool: Shame smog lost it for you. And if course, as stated earlier: PICS!:Big Laugh:
  22. Goldie Driver

    New Guy from S.Jersey

    Welcome from Houston, Texas ! That looks like a nice survivor. :waytogo: I'd fix the mechanical stuff and leave it as is otherwise. :cool:
  23. Goldie Driver

    700R4 Lockup Torque converter control issues solved

    On my 1980 TH350C (lock up converter) that green plug is a test point for the converter. Since the color is the same I would assume the function is the same for your 700R4.
  24. Goldie Driver

    What have you done to your square lately??

    Quote my own post - this '80 manual SHOWS a grease fitting, but nothing like the way mine is set up. No mention is made of it, though ... Consistent !!
  25. Goldie Driver

    What have you done to your square lately??

    9 years of ownership and many readings of a 82 FSM and no mention was ever made of this grease fitting on the NP205 shift lever . I just noticed it today while working with the cotter pin. Probably because it's DAM NEAR IMPOSSIBLE to get the hose on ...:mad: Oh, and added a cotter pin to a...

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,156
Members
43,334
Latest member
Nborden88
Top