Search results

  1. B

    Rear brake seem to be grabbing harder than fronts

    1986 1500 4x4 suburban Added 8 lug 3/4 ton complete set axles to front and rear and now rear brakes grab and lock up if too hard on the brakes. Not sure if this burban had this problem before because i never drove it with the 6 lug axles. Today i replaced the front calipers and tried...
  2. B

    no longer available

    The trailer seems really well built and does not look like it was used very much. Seems perfect for any type of parade or just pull it around the yard. Thats pretty much all i have ever done with it.
  3. B

    no longer available

    Hello all Selling my rough terrain munitions trailer. Its in cery good condition and the tires look really good. Has non skid deck. Feel free to reach out for questions. This trailer does not have a title and is not recommended for towing on public roads. Trailer is located at my home...
  4. B

    4

    Runs and drives. Current Texas state inspection. Many new parts. Clear Texas title in hand. Front axle works but makes popping sound from left front u joint. Two extra motors and a extra rear axle along with a extra transmission and transfer case available for extra. asking 9000
  5. B

    Questions about snow plows and mounts.

    I would not recommend a plow on a half ton chevy truck or suburban. The frames on the 1973 to 1991 are too thin and are prone to cracking, however the 3/4 ton and 1 ton frames are a bit thicker and more well suited to handle the weight of a plow. Some plows now days can be Poly which Ive...
  6. B

    Rollbar padding only sold in offset? Huh? Any engineers, builders or metal fab people to chime in?

    Got some solid ideas Thanks I’ll keep an eye out for those pool noodles and or some misc Hvac stuff.
  7. B

    Rollbar padding only sold in offset? Huh? Any engineers, builders or metal fab people to chime in?

    Just finished a 8 point roll cage and have been looking for some roll bar padding to put in areas around the driver. Last time I built a cage was about 17 years ago and I seem to remember we always just used round foam padding with 1 3/4 inch center diameter. Now all that seems to be out there...
  8. B

    14 bolt full floater before and after media blasting

    And paint
  9. B

    14 bolt full floater before and after media blasting

    80 bucks to have it blasted. Just need to install new seals an brake shoes now.
  10. B

    rebult 3/4 ton axles and blew both front and rear first time out hot rodding

    True Not a limited slip. I misspoke
  11. B

    Anyone have any leads on those 3/4 14 bolt axles for 200 bucks for a set?

    Thank you for the leads. The ff in the poconos with 3,73s is a deal. Here is a 4,10 ff I was able to pick up last Sunday 11-8-2020 for 200. The seller also sold me a good working sm465 connected to a np208 with a straight driveshaft for another 200.
  12. B

    rebult 3/4 ton axles and blew both front and rear first time out hot rodding

    The spider gears which were purchased new from Richmond only 3 months ago are completely destroyed. The carrier pin was stuck in the carrier. We used a cutting torch to remove the carrier pin. with another set of spider gears and new carrier pin she would be up and going again, but this sf 14...
  13. B

    Anyone ever install 8 point cage in a squarebody burban?

    Roll cage for a suburban
  14. B

    Can anyone identify this axle type?

    Skid steer to load it. 1940 ford 9n with boom pole to unload it.
  15. B

    Can anyone identify this axle type?

    I’m also wondering is the axle tubes are going to be the same diameter as the current 14bolt SF.
  16. B

    Can anyone identify this axle type?

    I bought it It measured about 40 inches in between spring perch to spring perch. everything I measured from the 1986 suburban 4x4 was almost exact as to the to this 14 FF “full floater”. hopefully this will hold up and not blow up after one 3 hours of drifting. it sure looks a whole lot more...
  17. B

    Can anyone identify this axle type?

    Was told it’s a 1982 ff. not sure if it’s a dually rear wheel or single rear wheel and or if it came off a 4x4 or a rear wheel drive. any help would be much appreciated
  18. B

    750 Holley double pumper fuel pump advice.

    Thank you I have always understood that double pumper meant that fuel can be sprayed in from the front and rear regardless weather or not mech or vac secondaries. I could be wrong and it would not be the first time or the last time. We have a fuel pressure gauge at the fuel rail on the carb...
  19. B

    rebult 3/4 ton axles and blew both front and rear first time out hot rodding

    Thank you Rear diff was a limited slip 10.5 inch ring gear. I had just replaced the spider gears, pinion seal, crush sleeve and outer wheel bearings and wheel seals.
  20. B

    Anyone have any leads on those 3/4 14 bolt axles for 200 bucks for a set?

    A while back someone noticed a set of 3/4 axles for sale in the Dallas,Texas area for $2000 and it seemed like quite a few people got in a uproar over the high priced axles and started saying how those axles were only worth a couple hundred bucks. well now that I have blown my axles im all...
  21. B

    rebult 3/4 ton axles and blew both front and rear first time out hot rodding

    1986 Burb with hotrod big block. Took her out over the weekend for some jumping and drifting at the local off road park. Blew something in the front axle on the drivers side, make a horrendous sound from the drivers side while in 4wd. Spent the rest of the day drifting and racing around on...
  22. B

    750 Holley double pumper fuel pump advice.

    Currently running a holley 750 double pumper with vac secondary's and while out hotrodding around and jumping I noticed that the current holley Mighty mite 34gph 7-10 psi electric fuel pump cannot keep the carb full of fuel when at wide open throttle. From day one the holley mighty might has...
  23. B

    wanted 1986 GM delco radio

    Just looking for a old Delco radio I can put in the suburban, prefer working but will consider non working. Im located in the Dallas,Texas area. This is a photo of the style radio wanted. Thanks
  24. B

    trade bucket seats for a bench seat

    Hello, They actually got sold already. Thanks, Viktor Cool and thanks but in that case would you mind closing the post as to not waste anyone elses time or mark sold?. Thanks
  25. B

    Anyone in the Dallas,Texas area have the .530 valve guide machine tool?

    The tool is a bit expensive but a must if running the small valve seals that allow for triple valve spring clearance. shucks

Latest posts

Forum statistics

Threads
42,125
Posts
909,625
Members
33,618
Latest member
1975K20
Top