Search results

  1. liam

    Any holly sniper 2 experts here

    I just put a sniper 2 on my truck and had an inline fuel pump but it didnt work very well because there was no where to properly mount it do i got the holley intank fuel pump and that worked very well and then the truck sat 2 weeks getting a new driveline and now it runs like crap again any ideas
  2. liam

    Holley sniper 2 acceleration problem

    So I recently installed a Holley Sniper 2 on my square and had a few problems but all those have been resolved so I think but yesterday when I went to drive it on the street I didn’t get to turn out of the driveway before it turned off but it fired right back up and I would go 20 feet and the...
  3. liam

    I need a Holley Sniper 2 expert

    I recently got a sniper 2 efi with the pdm and hyperspark distributer and I got it to run once but now the 5 inch dash says the ecu is disconnected and the fuel pump doest prime any ideas.
  4. liam

    Holley sniper 2 no fuel pressure

    I just installed a sniper 2 and the first time I tried to start it it wouldn’t start first thing I looked for was fuel pressure at the regulator and it was at 0 psi I have been fooling around with it all day and I am getting fuel but it still shows no fuel pressure and there isnt a lot of fuel...
  5. liam

    Backfiring

    Truck is backfiring when it goes over 1000 rpm already adjusted the carb and timing any ideas on what’s going on
  6. liam

    Help

    I recently got a new project that i got running today and when i went to move it the truck wouldn’t move but i dont know how that could be because it has had a remanufactured transmission put into it in 2016 and i already checked the fluid and topped it off any ideas
  7. liam

    DNE2

    Does anyone know how to use one of these things
  8. liam

    Fresh rebuilt 700r4

    I recently had my 700 go out in my truck i was driving it down the highway doing 75mph and was in 4th but then the trans went into 1st all of the sudden and would not go out of first so i pulled the trans and had it rebuilt buy some joker who has had it for 5 months and just finished it i am...
  9. liam

    Any idea what this is called

    Its on a 208 transfer case what is the name of it
  10. liam

    700 r4 trans wiring

    Does anyone have a diagram of the wires that go down to the transmission
  11. liam

    Is this worth it

    I was just looking at trucks today and found this gem it has a 383 with a 10 inch lift but he wants 7000 for it
  12. liam

    Griffin radiator no heater core outlet

    I recently bought a Griffin radiator and it has nowhere for the heater core hose to go is there an alternative
  13. liam

    Wiper switch

    I just put in a new windshield wiper switch on my k20 and now they won’t turn off and only have one speed which is high any ideas
  14. liam

    Idle problem

    since I bought my 1984 chevy k20 last August i have put on 3 different carburetors on and each time i adjust them after you turn off the truck and start it again it will idle at 1500 rpm any ideas
  15. liam

    Flywheel

    what is the torque spec for a flywheel on a 350 small block
  16. liam

    Tv cable

    How do you adjust the cable that goes from the transmission to the carburetor truck will not get out of 1st gear
  17. liam

    Hydro brakes

    Does anyone know if hydro brakes are worse than vacuum brakes or are hydro brakes better
    • liam
    • Thread
    • Replies: 4
    • Forum: Brakes
  18. liam

    700 r4

    I was just driving my 84 k20 with a turbo 700 r4 and I was doing 55 and steeped on the gas and the rpm went up to about 4000 and it would not go any faster and then I pulled over and tried to go again and I couldn’t get it out of 1 gear I was just want to know if i need a new transmission
  19. liam

    Avs2 problems

    I have a 1984 chevy k20 with a 350 and an Edelbrock 650cfm avs2 and after installing the avs2 it always seems to unadjusted itself i have had to adjust it 7 different times I dont think that is very normal

Latest posts

Forum statistics

Threads
48,413
Posts
1,066,819
Members
42,794
Latest member
Huffer8
Top