Search results

  1. MrMarty51

    6.2 tune up

    I have a 2000 K3500 with the 6.5 and I like that truck a LOT. I use the Stanadyne performance formula fuel additive. Also, since the fuel of these days is so low in sulpher, I add an ounce of Walmart brand TC-W3 two stroke oil for every two gallons of fuel that it might take to fill the tank, if...
  2. MrMarty51

    Guess The Tool

    Top pic. looks like a double ended doodaingrrrrr. Oh wait, that's what two girls use. :anitoof::happy175::happy175::happy175:
  3. MrMarty51

    Guess The Tool

    Actually, the jaws are set each side of the nail head, then the slide hammer is activated to drive the jaws to below the surface of the wood so that the jaws can grip the shank of the nail, then the whole tool is rotated so that the lever of the one jaw is resting on the wood, then rotated...
  4. MrMarty51

    454 knock - looking for suggestions

    Pull one spark plug wire at a time, with the engine running. If the knock goes away on one or two cylinders, those are the cylinders with the rods knocking. If the knock gets louder, then, it is a piston or wrist pin problem.
  5. MrMarty51

    New to squarebodies with 81 k30 crew cab

    That's a real nice truck. Thank You for showing it to us and welcome to the forum.
  6. MrMarty51

    Just Left Shop Help Pls!!??

    :happy175::happy175::happy175::happy175:
  7. MrMarty51

    Vacuum

    Yeah, welcome to the forum Steve.
  8. MrMarty51

    my better halfs new project

    My son has two 60s Scouts. Turns out the one that came without a title is a "Red Carpet special". only 1000 of them made. He now has a title for it. Legally.
  9. MrMarty51

    Not new, but must get post count going to paticipate in classifieds!

    Now that is a goooood woman. Welcome to the forum.
  10. MrMarty51

    North of The 49th

    Welcome
  11. MrMarty51

    Steering Column Bearings - HELP

    Yeah, welcome to the GMSB forum 251.
  12. MrMarty51

    Idles fine but stalls when put in gear!!

    Accelerator pump is bad. Remove air filter cover, look down the bores, open throttle, should see fuel spray into the front bores of carb.
  13. MrMarty51

    What's the most dangerous tool in your shop?

    You beat Me toooit. Nothing more dangerous in My garage than My ability to do stupid stuff.
  14. MrMarty51

    What have you done to your square lately??

    I am watching more snow falling on the 78 K20. That's about all.
  15. MrMarty51

    Bvllsh!t on craigslist.

    I think it`d be a fortune maker to get one of those 900 numbers, list it as 1-900-insults or some such. For those that can not live without their daily insults.
  16. MrMarty51

    Bvllsh!t on craigslist.

    This aint C.L. but it might get some ones attention in here. http://www.thetruckstop.us/forum/threads/1986-4x4-gas-burb.46869/
  17. MrMarty51

    1987 TBI wont start, no spark, but has fuel

    I`ll sell You a 91 K1500, everything is there, just needs the engine gone through, or another engine. A no rust unit too.
  18. MrMarty51

    1987 TBI wont start, no spark, but has fuel

    That TBI 350 will run for a very long while if it is taken care of. It will drink a whole lot less fuel too. The 87 K1500 that I once had would get 17 to the gallon, I will guarantee You will never get that from a BB. The four barrel sniper system might be a nice upgrade for the 350 though...
  19. MrMarty51

    Im a 6.2 Diesel guy

    Welcome to the forum Dakota. I recently tried to buy a CC square body 2 wheel drive that has a 6.2 in it. I love Me some diesel. My current main truck is a 2000 K3500 with a 6.5 and has a few nice uprated components added.
  20. MrMarty51

    1

    Nice build You have going there. I`d like to find a nice CC body to convert My stuff over to.
  21. MrMarty51

    350 to 400 small block

    I once did a 350 with three deuces into a 72 Vega notch back. It was quick
  22. MrMarty51

    350 to 400 small block

    I have a 400 SBC setting in the shed, bored .030 over and ready for fitting pistons. It has the main bearing caps too. No heads, not rotating assembly, just the block. If You know of someone getting near Billings Montana, I could send it along. I live 150 miles to the east of there but could...
  23. MrMarty51

    New Member and New to Chevys

    I love diesel, I love new diesel in old trucks. Welcome to the forum and yes, please post pics of the progress, curious minds wants to watch.
  24. MrMarty51

    New swap project in the planning stage right now

    Whatever way You go, have one four weeeel drive.
  25. MrMarty51

    TBI rough on a warm or hot restart

    Could be the temp sensor or the O2 sensor.

Latest posts

Forum statistics

Threads
45,956
Posts
996,958
Members
39,158
Latest member
cutlerfab
Top