Search results
-
-
77 K10 Cab swap questions
It’s a lot less work then going the other way, everything will transfer over, if you go 86 and put a 79 cab on you have to make modifications to the upper front cab corners like my nightmare lol, originally my dad just cut the rectangular holes to accommodate the newer style hood hinges, but you...- Tank6x2
- Post #2
- Forum: Paint and Body
-
Rims
It’s not a must though, your able to remove fibreglass fenders, offset is a choice not a must…can always switch out the hubs for a k20 on the front… it’s dependant on what look a person is going for versus usability… Just MO- Tank6x2
- Post #4
- Forum: Wheels and Tires
-
What have you done to your square lately??
Getting ready to support the new face, just have to fill in the gaps -
K5 weight without drivetrain??
Can always trailer it to a cat scale at the truck stop- Tank6x2
- Post #3
- Forum: Tech Discussion
-
K5 weight without drivetrain??
Last shell I took in was 2400lb- Tank6x2
- Post #2
- Forum: Tech Discussion
-
-
Dana 60 front diff
Repost in a different thread with label of point to point - I’d bet there’d be interest -
1983 k5 blazer stalls when no pushing gas pedal.
Grab yourself a timing light, cheap investment and then I’d lean vacuum leak, LIGHTLY spray brake or carb cleaner around the vacuum lines going in small areas to see if it picks up the idle any where… if you don’t have anyone to help grab a bungee cord to hold the throttle open a little to run...- Tank6x2
- Post #2
- Forum: Tech Discussion
-
Windshield washers
I always remember the ones in the cowling, wipers would be ideal I think- Tank6x2
- Post #2
- Forum: Tech Discussion
-
Rear shock brackets
easier to carefully cut them off as close to the axle tube as possible and then flush the weld off, clean off your new area, reshape and weld again.- Tank6x2
- Post #2
- Forum: Lifted & Off-Road Systems
-
TH 350C Torque Converter
any other identification markings on the TC??- Tank6x2
- Post #2
- Forum: Automatic Transmission
-
208 swap out for 205.
have you tried researching in the search tab for the answer?- Tank6x2
- Post #2
- Forum: Transfer Case
-
My 78 Custom Deluxe gets a new gear ratio
Nice job bubba!- Tank6x2
- Post #2
- Forum: Differential & Driveline
-
Cab rust repair help-- Which panels do i need?
79 converting to 8668- Tank6x2
- Post #11
- Forum: Paint and Body
-
What have you done to your square lately??
Still doing hood mod, starting the other side now -
Cab rust repair help-- Which panels do i need?
They never end, wait till you modify !- Tank6x2
- Post #8
- Forum: Paint and Body
-
-
Cab rust repair help-- Which panels do i need?
It all makes sense when it’s apart- Tank6x2
- Post #5
- Forum: Paint and Body
-
Seat covers, looking for recommendations - later in the thread reports on how my cover is holding up
No I don’t, but I have had one in the past, worked well enough, it’s a wear item, your hopping in and out so take it for what it’s worth that it’s a cover -
inline six compatability
1962-1988 for the GM V6, check out The Novak Guide to the GM TH400 Automatic Transmission online for a little bit of history on your th400- Tank6x2
- Post #2
- Forum: Carb Fuel Systems
-
Rear end shake upon acceleration
Centre shaft support bearing or mud/snow or ice caked on the inside of the rim, beyond that check your universal joints while your there…- Tank6x2
- Post #2
- Forum: Introduction
-
Seat covers, looking for recommendations - later in the thread reports on how my cover is holding up
B078XCVKDK Enter this into Amazon .Com and it’s yours for 40$ -
Decent looking body my brother saw on fb
Just a aftermarket installation I would think- Tank6x2
- Post #2
- Forum: eBay & Craiglist Listings
