Search results

  1. P

    Best method for adding a fuse box/accessories?

    did this work?
  2. P

    constant power b+ I need the right plugs for fuse panel

    I know on my fuse panel there are several constant positives around the orange wire in the upper left corner of the fuse box. I purchased standard motors ET 461 ignition taps, and they do not work in the battery locations. they do work in the key on ignition ports. Does anyone know the...
  3. P

    Single din install problem

    thats nice, but I have a floor shift tcase and I dont want to encourage my teenager to be loowing down quite so much. Great for an adult tho
  4. P

    voltmeter diode replacement?

    well, after a lot of internet scouring on other web pages, I have found out a few things. The stock resister is 127 ohms. you can get them from new boyz square body, OR from digikey and mouser as stated above. I have verified that mine will work with the correct resistor after getting one of...
  5. P

    voltmeter diode replacement?

    the one with the battery at the bottom of the gauge
  6. P

    voltmeter diode replacement?

    any idea what value is needed for a voltmeter. This is definitely not in my wheelhouse.
  7. P

    voltmeter diode replacement?

    anyone know where to buy a new diode for the back of my voltmeter. I suspect mine is broken and cannot seem to source them.
  8. P

    What is you headlight setup

    im not an LED fan. I searched for a long time and ended up with LMC clear replacement housings. I was hoping to find glass ones, but settled for their plastic housings which are adequate. I then found higher wattage bulbs, and made my own wiring harness for the bulbs to get full battery...
  9. P

    gauge refurb?

    so voltmeter is totally not working. When probing the two terminals on it voltmeter, I do not get any OHMS reading between them at all. So I am guessing the resistor is dead? I checked the harness itself. All grounds have continuity, as do the temp and pressure leads, and they are attached...
  10. P

    RETRO-Mod: Jeep intermediate steering shaft

    whats the difference in later jeeps? 97 and up? edit: called borgeson. The earlier is 1" DD and the later is splined.
  11. P

    gauge refurb?

    I think I need one of these? At least I only have two and there is a space for three. https://www.ecklers.com/1981-1987-chevy-gmc-truck-instrument-panel-printed-circuit-retainer-61-889024-1.html Edit: After looking through that below video again, I see he only has 2 prongs at the voltmeter...
  12. P

    gauge refurb?

    so water, volt and oil all tested fine independently using the 9v batter. I am missing one of the little clips for the volt meter. No idea where that went. Can they be sourced? If they are no longer available but from a junkyard, what years would have them as you all know the old trucks are...
  13. P

    gauge refurb?

    Was watching videos of how to refurb, clean etc gauge clusters last night. 1. One of the videos showed that using a 9v battery, one could test the gauges by touching the back of cluster, the little prongs that hold the gauge terminals. When I do that, only the oil pressure gauge moves. ANd...
  14. P

    Single din install problem

    thanks all. Finally found that metra kit on late night intenet search and ordered it. Im guessing that is why the PO bent the ears back instead of cut them out, so that it may be returned to a two post.
  15. P

    Single din install problem

    its already been hacked. I can either weld this back up, or weld in a patch panel I guess. Ill have to look into the 2 knob thing. do you mean a retro sound radio?
  16. P

    Single din install problem

    bought an 87K5 for my highschooler. trying to install a single din. Aside from the fact that all the wiring is hacked and connections are made with household wire nuts, Im making progress cleaning all that crap out. I found the yellow, black and gray wires and have read I will need to install...
  17. P

    Seat belt retractor

    my 87 shoulder belts have a tumbler device in them that cams a lever up to lock the belts. They retract when the door is open, and otherwise not very well. Its pretty annoying.
  18. P

    seat belt and top hardware? need to source new bolts

    the seat belt uses a 12 1.75 bolt but I "think" they are a cutting thread??? Has anyone used a standard metric thread pitch without issue?
  19. P

    seat belt and top hardware? need to source new bolts

    sorry for the newb question. I recently replaced the floors in my sons new to him 87 K5. i reused the seat and seatbelt bolts that plug weld on to the underside of the floor. The bolt that secures the female side belt to the floor is all rusted out. I think its metric, but cannot find any...
  20. P

    Cup holder conversion for center console

    so I popped the "cup holder" portion of the console off. Its a nice flat area now that would be easy to make a fill plate. Just need to find a press in style cup holder.
  21. P

    Cup holder conversion for center console

    thank you. I have an 87, so that doesnt appear to work. Ive sent them an email to see if it does.
  22. P

    Cup holder conversion for center console

    sorry for the newb question, but I have been searching all morning. I have seen a conversion piece that will get rid of the square pockets in the factory 87 console I have, and allow for cup holders. I cannot find that again however. Does anyone know who makes those, have a link etc? Or...
  23. P

    replacement Parking lamp sockets? Sockets fall out of housings

    the delco ones are much better, thank you
  24. P

    replacement Parking lamp sockets? Sockets fall out of housings

    nope. I have the gasket. Even the factory ones are loose and kept falling out of the factory housings, but both sockets and housings were fairly worn. Was thinking new sockets and housings would resolve my issue, but did not. Wonder if there is an unpdated socket and bulb that would work...
  25. P

    replacement Parking lamp sockets? Sockets fall out of housings

    New to me 87 K5. Going thru electrical stuff to get it safe for my son. The front parking lamp sockets were falling out of the factory housings, not to mention they were super hazy. I replaced the hosings with clear units from LMC, and found that one of the sockets was bad in the process...
View older results

Latest posts

Forum statistics

Threads
45,954
Posts
996,841
Members
39,153
Latest member
Oliver90_08
Top