Search results
-
Wheel help/opinions
Yep. 2" drop shackles in the back and 1 coil cut in the front.- brooksman9
- Post #22
- Forum: Wheels and Tires
-
Wheel help/opinions
Thanks for the pics. That helps. I'm not quite as low so I plan to stick with the 60's. I think the 235/70-15 I plan to go with on the front will fit similarly to the rear with tire to rim width ratio. Should both look pretty vertical. Just need to get some more body work done and then I will...- brooksman9
- Post #20
- Forum: Wheels and Tires
-
Wheel help/opinions
Ok, trying to get an idea of how the 10" 275/60-15 might look on the back. Side wall would be a little more vertical on it but I think the depth would be about right. This is the 275 on an 8" wheel off of my Camaro. Bolt pattern is different so I can't mount it but setting up against the studs...- brooksman9
- Post #18
- Forum: Wheels and Tires
-
-
-
-
Cowl Induction or stock?
That truck looked very nice before it got smacked. Not digging the wheels. Either hood would look good. I hate hood ornaments. Just my opinion. Hope you get it fixed back up soon.- brooksman9
- Post #8
- Forum: Exterior
-
Steering Wheel Cleaning
Used some Dawn spray foam on one yesterday. Worked fairly well.- brooksman9
- Post #6
- Forum: Interior
-
-
-
New NVU Gauges
Will those fit in stock locations? Never done any gauges yet.- brooksman9
- Post #6
- Forum: Gauge, Speedo & Instrumentation
-
-
What have you done to your square lately??
Didn't take any pics but installed a catalytic converter ( 8" Flowmaster ) and sway bar disconnect kit on the K10 today. Wanted to take a back wheel off the Camaro and put up against the C10 to get some rough ideas on sizing but I couldn't find the wheel lock key. :mad: I did at least find the...- brooksman9
- Post #20,770
- Forum: Garage
-
-
-
Ferd for my Granddaughter
I have some kind of old Ford q-jet (I think) carb that was on my c10 when I got it. If anyone have a use for it it is theirs.- brooksman9
- Post #9
- Forum: Other Vehicles
-
3M Tape on cab moldings
They make special trim screw you can use to put the molding clips on if you desire to go that route. They would take the place of the little posts. Same as for windshield molding. You can get them on ebay cheap.- brooksman9
- Post #9
- Forum: Exterior
-
Wheel help/opinions
Ok. Question is will the 10" wheel fill the wheel well more or not even be enough to notice?- brooksman9
- Post #12
- Forum: Wheels and Tires
-
Wheel help/opinions
235/75-15 all four corners right now. That's what was on there when I got it. I like the more old school big and little also but not too little in the front. Also want.to fill the wheel well as much as possible. Staggered is ok with me but just don't want it to look wierd.- brooksman9
- Post #9
- Forum: Wheels and Tires
-
Wheel help/opinions
Also considering a 255/60-15 for the front.- brooksman9
- Post #6
- Forum: Wheels and Tires
-
-
Wheel help/opinions
Looking at some wheels for the C10. Most likely 15" AR61's. Thinking about 275/60-15 on the back and maybe a 235/70-15 on the front as they are right at the same size. I have dropped the back with 2" drop shackles and cut 1 coil from the front for roughly the same. Hoping it will fill the back...- brooksman9
- Thread
- Replies: 24
- Forum: Wheels and Tires
-
What have you done to your square lately??
Had an old Jegs exhaust kit off one of my Camaro's. Hung it on the truck so it's not open header loud. Rather quiet now. Too quiet.- brooksman9
- Post #20,713
- Forum: Garage
-
-
New Old Guy with 76 C10 Shortbox
That’s a good lookin truck. Sits just right in my opinion. Welcome- brooksman9
- Post #14
- Forum: Introduction
