Search results

  1. nvrenuf

    Seat options '90 Burb

    I could be wrong but I don’t think any square body ever came from the factory with power seats.
  2. nvrenuf

    Trying to remove plastic knob on side vent

    Seems like there’s a clip at the far end on the vent flap. Be careful with it, I believe those are discontinued and good one are hard to find.
  3. nvrenuf

    Spark plug gap closed fresh rebuild

    A compression tester will screw into the spark plug holes. Removing all of the plugs will make it easy and faster to test. The actual compression reading will vary depending on the compression ratio from engine to engine based on the parts used, just look for the readings to all be very...
  4. nvrenuf

    Spark plug gap closed fresh rebuild

    Pulling the cover won’t show anything relevant to inside the cylinder. At this point, I think I’d install a new plug and roll the motor over a few times by hand to see what you feel and then check the plug.
  5. nvrenuf

    Spark plug gap closed fresh rebuild

    Note that it didn’t just close the gap, the porcelain is knocked off center.
  6. nvrenuf

    Gear swap

    The 80 dually would have a D70HD, I don’t know what the 05 would have but I do know they did not us the HD IF it had a D70. Need to figure out what axle is in the 05.
  7. nvrenuf

    Spark plug gap closed fresh rebuild

    Are you sure that’s the correct STYLE of plug for your heads?
  8. nvrenuf

    tranny mount/crossmember- urgent help needed

    How's the front? It should be worse but you may get by because of the low lift.
  9. nvrenuf

    1990 v3500 crew cab 8 foot box, new owner

    Pics or it didn’t happen! Welcome from the South! :favorites37:
  10. nvrenuf

    tranny mount/crossmember- urgent help needed

    If you not comfortable with the spacers on the crossmember don’t look at the steering box bolts. lol Also, keep in mind that when spacing the tcase down to improve the rear driveshaft angle, you are making the front driveshaft angle worse.
  11. nvrenuf

    tranny mount/crossmember- urgent help needed

    The spacers are on both sides and all of the hardware is the same size. Be sure the replacement spacers go on top of the frame like the remaining ones are (or should be).
  12. nvrenuf

    What new tools have you got lately?

    @Mr Clean great info, thank you!
  13. nvrenuf

    Car Hauler tips/tricks/ideas

    It seems like running the strap through the wheel would leave rub marks on them.
  14. nvrenuf

    What new tools have you got lately?

    I've been staring at those belt sander attachments on Amazon forever. Do you know what brand you have? Are replacement belts readily available? There are so many cheap versions I'm afraid of getting one that I can't get replacement belts for.
  15. nvrenuf

    Best 454 all around build

    Your going to get all kinds of suggestions but here’s my .02 I’d keep the 4.10’s if you intend to ever tow with the 33’s - especially if you were to go to an overdrive trans. For a carb in a non hot rod street truck, I highly recommend a quadrajet. There’s no need for a Holley and a well...
  16. nvrenuf

    Car Hauler tips/tricks/ideas

    @bluex be very careful strapping to anything above the axles, the suspension can still cycle as the trailer goes over bumps etc causing those straps to have slack and possibly come loose. The only way to successfully strap to anywhere above the suspension is to pull it down until it’s on the...
  17. nvrenuf

    Are my gears to high for the setup?

    More gear for 35’s, I’d go with 4.10’s or 4.56’s.
  18. nvrenuf

    Bowtie Brush guard.... Opinions?

    It’s a no for me.
  19. nvrenuf

    TH400 Slipping When Warm - Chunks in Oil Pan

    @82sierradude you knew the answer before you made this post…
  20. nvrenuf

    What new tools have you got lately?

    Yes, that is the pivot pin puller
  21. nvrenuf

    Any black two tone trucks out there?

    I always loved the factory black / silver two tone scheme.
  22. nvrenuf

    Looking for a replacement frame/ chassis for my ‘86 K30

    You'll get more traffic by posting this in the "Wanted" forum. You probably want to specify if that is a regular K30 pick up frame or a cab & chassis frame (if C&C, add the wheelbase).
  23. nvrenuf

    No line pressure to rear disc conversion, no prop valve

    I don’t know that the m/c is definitely the problem but calipers use more fluid to move than a wheel cylinder, a lot of people change the m/c during the conversion.
  24. nvrenuf

    Replaced Radiator, but no heater hose hole!!

    There’s more to it than rerouting the hoses. Since it’s obvious it’s not the right one the next question is if it’s the right size.
  25. nvrenuf

    Replaced Radiator, but no heater hose hole!!

    Idea: take the wrong radiator back and make the seller get you the correct radiator??

Latest posts

Forum statistics

Threads
45,953
Posts
996,786
Members
39,151
Latest member
grego28
Top