Search results

  1. Craig Nedrow

    Engine Swap Transmission Selection

    I had my 4l60e in my 98 z28, rebuilt at a local shop where I know the guy, but didn't last. Built my 350 at home using two books, and some videos. Yes I did have some troubles, had to take it back apart a few times, but though nervous whin I installed it, it worked amazingly well. It was behind...
  2. Craig Nedrow

    BBC 489 build

    More done, I had the piston on backwards, was so excited to try it out, but now nothing hits. What a relief as I paid to have the motor balanced to .2 grams, not the usual 2 grams. Pulled apart again, and painted the block black because it is more thermally efficient then the blue.
  3. Craig Nedrow

    1974 c10 didn’t start-fuel problem?

    $400 buck is $400 bucks....but I replaced both tanks, sending units, valve (six way) and cab switch and nary another fuel problem. You can see part numbers and install here: https://www.gmsquarebody.com/threads/new-for-me-1985-silverado-20-6-2-diesel.32359/page-5 page 5 starting at post 65
  4. Craig Nedrow

    who can help identify this frame?

    The S10 frames are used in many 47-55 1st series trucks, almost a bolt on there is a f-book group dedicated to this: https://www.facebook.com/groups/1316351842443154. I may go this route for my 54. Nothing wrong with what you are doing though.
  5. Craig Nedrow

    18x10 front and 18x12 rear who's done this? Look inside.

    rubber band tires really pull you around on the grooved big truck highways around here, just a consideration.
  6. Craig Nedrow

    BBC 489 build

    Surprisingly, no interference with crank so also a plus. Massive interference between the head and piston. Checked piston CH +1.280 so that is correct, and the rod length is 6.386 with calipers, supposed to be 6.395, so close enough. So winning some and loosing some. I did an extensive...
  7. Craig Nedrow

    BBC 489 build

    Deburr bearings on both sides, install crank with light oil, and spins freely, so no line bore needed. Installed piston and rod on #1 deck height is about .015, so ok. Indicator used to find TDC.
  8. Craig Nedrow

    BBC 489 build

    Brought my 454 aka 489 home from the shop, it was later in the afternoon, so I did not get to much done. However I did set up my bore gauge to 4.280 and measured one bore, and it was exact from top to bottom, and at 90 degrees, so very pleased. So round and straight. I will trial fit the crank...
  9. Craig Nedrow

    Replacement doors?

    The worst part is you need to strip the existing stuff off first b-4 painting. Soooo paint remover, clean, dewax, epoxy primer, color, and clear. It will make everything else look like poop. HOWEVER the door will look awesome. BTW take your bog boy wallet to the paint store.
  10. Craig Nedrow

    Trying to identify this color of blue

    this might help, #29 85: https://www.cjponyparts.com/resources/chevy-c10-paint-codes#1978
  11. Craig Nedrow

    Replacement doors?

    Bought mine from Brothers now holly, look good.
  12. Craig Nedrow

    BBC 489 build

    Got a call, will pick up the engine on Monday...Yeah!!
  13. Craig Nedrow

    86 1/2 ton gears needed for 33” with new 383

    There are 383's and then there are 383's. Engine internals will dictate where your torque will be rpm wise, and also how much torque overall, anywhere from 300-500. 2.73, 33" tires, 2000 rpm's and .67 OD=about 107 mph. Just changing to 3:73 = 78 mph. 4:10=71 mph. 4:56 = 64mph. Bucket is on the...
  14. Craig Nedrow

    Oil pan off, anything I should do while I’m under there?

    Just seal it up, save the money on the oil pump as they last almost indefinitely. When you rebuild (if keeping the same motor) pull the pump apart and inspect it. Get a good book on the build. I like the 454 way more then the SB, would never go back.
  15. Craig Nedrow

    Father-Daughter Shop Day

    Some girls are mechanical. My oldest, Leah, started early, would take her up when she was little five or so, give her some tools and an ol' YF carter and she was happy for hours. Leah is in her 40's now and works with her husband on there rigs. She also has branched out into woodworking. Sooo...
  16. Craig Nedrow

    Eastwood Versus POR15

    Craig85 turned me on to this stuff, It's great.
  17. Craig Nedrow

    Eastwood Versus POR15

    Wire brushed my frame, degreased, black epoxy primer, Magnet Chassis black, on clear coat, but I should have, ran out of time. Used POR15 on the 55 panel engine bay, completely chalked out in five years, repainted after prep with Duplicolor and has worked well.
  18. Craig Nedrow

    Old Bedliners

    Mine was a little different in the 73 K20, but when I started my build, I pulled it, and there was quite a bit of rust.....I will Rhino line it like I did on the 85 when it is finished. Grandson learning to Rhino line, this is underneath.
  19. Craig Nedrow

    No accessories power

    Pics First is off position, second is power on, next position on second pic going left would be start. On my 73 K10. I use that little screwdriver to start this truck, been that way for years, don't drive it on the road much, 100,000 miles of huntin and rocky hills have wore out the ball joints...
  20. Craig Nedrow

    Gas to diesel

    It was a machinist at a military installation, Yakima Training center in Selah. I fell in love with those 6-V-53s that they put in a lot of those rigs not only did they sound bad to the bone. They really hauled butt too, cause they were both turboed and supercharged. I hated the 6.2 in the C20...
  21. Craig Nedrow

    8 lug slots...?

    I agree, they did everything for me for years, tractor, truck, car pickup. A few years age needed tires for the Buick, they were **** lasted less then 30000, so took the car back, and no warranty. Had one replaced that was really bad, full price. So while I was there I looked for a us based...
  22. Craig Nedrow

    Custom fabric inlays on dash side panels- how to attach fabric?

    I once used that 3M stuff on my bosses chair, cause he ticked me off for pickin on a kid. put on two coats, ten minutes later, came storming through the shop plopped down in that chair, and got a funny look. Tried to stand, the chair stuck to his britches and arms, had to push it off. later we...
  23. Craig Nedrow

    Hello from Hawaiii

    You get a * for posting pictures on your first post, yeah these guys can be such pictures hoes. Glad you're here, Welcome
  24. Craig Nedrow

    New Gas tank installation

    ^^^^^^^I did buy a new filler and vent hose from Brothers, now holly. https://www.gmsquarebody.com/threads/new-for-me-1985-silverado-20-6-2-diesel.32359/page-5 Start on page #5 post 65 to see the pictorial method.
  25. Craig Nedrow

    Engine & transmission removal & reinstall general tips

    Six bolts a couple wires, and the whole front end comes off, what I always do. I also have a adjustable tilt lift that has four chains at the corners of the engine. I just don't want to damage anything getting the engine out. Speaking of such, It will take an extra hour of finagling and...

Latest posts

Forum statistics

Threads
45,947
Posts
996,585
Members
39,141
Latest member
jbwhitford
Top