Search results

  1. Jgonick

    Seat Belt Rebuild

    I used 73-87 Chevy/GMC Truck Seatbelt Restorations in the past and was pleased with the results. Facebook-link
  2. Jgonick

    Help Please - Fighting new Gremlins

  3. Jgonick

    dumfounded

    Original setup on 85 attached Link- to wiring diagrams
  4. Jgonick

    '73-'76 turn signal switch not universal

    Incandescent or LED light bulbs? If using LEDs you will need a electric flasher- not an original thermal flasher. LEDs do not use enough current so thermal flashers don't work properly -If this is your problem- be aware that the electric flasher poles must be correct.(sometimes they are...
  5. Jgonick

    Wipers won't stop

    EDITED: Nope guessed wrong. I looked at a picture of the wiper dash switch online- I'm not sure now. _ sorry. Maybe someone else will know. I'm guessing- probably a GM Pack-Con III Series Terminal Female- 20-18 Gauge
  6. Jgonick

    Gas Gauge Off The Deep End

    If anything lowers the flow of current the needle moves towards Full. (or 3 O'clock with no current) so possibly a bad connection with sensing wire (pink) or bad ground. If both tanks are doing it- I would start by checking the pink wire connection at the fuel selector valve & firewall...
  7. Jgonick

    Wipers won't stop

    What do you mean exactly by messed up? Bent or plastic is melted etc.. Picture would be helpful. You have a few options- I generally just try to replace the pins (they will usually come out of the connector by pressing on a tab- every pin is a little different on how to remove them). If the...
  8. Jgonick

    Horn troubles

    At the horn relay (in the convenience center) Orange 240 wire brings power from fuse box (horn fuse) to relay. Black 28 wire goes to horn button. When you press the horn button it grounds the black wire which grounds the circuit. This causes the relay to work. (relay is an electric switch)...
  9. Jgonick

    Wipers won't stop

    Does the washer work? If you unplug the wires from the switch do the wipers still run? If they do not run, it is the connection to the switch or switch itself that is the problem. If they continue to run you probably have a wire that is grounded somewhere. Attachments are how to diagnose...
  10. Jgonick

    Wipers won't stop

    That sounds correct. Basically you are removing the delay module. "little box". Attachments show wiring for delay module & no delay module
  11. Jgonick

    Cab Light/Headlight Switch

    Sorry if this is obvious- but I've got to ask. When you are trying to turn it off by twisting the knob- you do have your door closed- correct? turned all the way left- is on & it just takes a small turn towards the right to turn off
  12. Jgonick

    Cab Light/Headlight Switch

    Replaced the knob or the entire switch?
  13. Jgonick

    Wipers won't stop

    possibly OR one of the wires (purple or gray) could be grounding somewhere before they get to the switch. I'm assuming the wipers start as soon as the key is turned. Would help to give us a little more info. Delay or no delay module?
  14. Jgonick

    Wipers won't stop

    correct. attached is a simple diagram of how it works.
  15. Jgonick

    Turn signal switch

    i actually do this and tape the wire ends (pins) together with a string to feed it down the steering column when replacing the turn signal switch. So much easier feeding it down the column without the connector on it.
  16. Jgonick

    Turn signal switch

    Like @Goldie Driver said- check the connection first. Also need to ask- Is changing turn signal switch the only thing you did or did you also do something else like changing bulbs? (Incandescent bulbs or LEDs)
  17. Jgonick

    '77 C10 350/TH350 ignition problem

    This might help- It goes into detail how to put the column back together. You are probably around page 28. I would read a little before that page and through the next few to get an idea of how it goes back together. jazzman- LINK-Inside the GM Tilt Steering Column
  18. Jgonick

    Turn Signal Issues

    Incandescent or LED bulbs? With incandescent- Front park/turn lights use a two filament bulb. One filament will blink with turn signal the other filament is the the park light. (brake lights are also two filament bulbs) Hazard lights are fed by a different power source than turn signal...
  19. Jgonick

    Starter and Alternator wires

    Just a FYI- On the wiring diagrams the first number (before color) is wire size in metric. The number after the color is the circuit. Example 3 PPL 6 would be 3mm Purple 6 = 12 gauge Purple 6
  20. Jgonick

    Starter and Alternator wires

    Here is a link to the wiring diagrams Link-wiring diagrams
  21. Jgonick

    washer pump not working

    Or you could try to fix yours if you wanted to try- here is a post with a video link (later in the discussion) describing how to fix it. LINK- to post LINK- to video
  22. Jgonick

    More Washer Pump Questions

    You should be able to- WHT 93 wire will brings 12 volts from the fuse box. PNK 94 goes back to the switch where it is grounded. Same wire setup on 85 & newer except the wires just goes to a separate pump (like the one in your link).
  23. Jgonick

    Wiper Pulse Module #15598496

    Looks like it is a diode. diode 1N4002
  24. Jgonick

    Fuel Gauge Blues

    I briefly looked for a ceramic resistor ~90 ohms- I didn’t have much luck. I was only able to find used ones on ebay. New gauges do not use the resistor. Also the new gauges are roughly $50 Example of new gauges at LMC -LINK Also a good video to really help you to diagnose the problem...
  25. Jgonick

    LMC AC controller has too many detents

    Surely they didn’t put the graphic (front) on a wrong switch- but I guess anything is possible. My suggestion is to call LMC and ask. I’ve had to call them in the past to clarify a description on a certain part. They were very helpful when I called.

Latest posts

Forum statistics

Threads
45,661
Posts
988,810
Members
38,756
Latest member
winterhawk
Top