Search results

  1. Stepside Billy

    What have you done to your square lately??

    Well surprise! Turns out to be the caliper hanging up. Didn't think about that because it's only a year old!!
  2. Stepside Billy

    What have you done to your square lately??

    Fired up the air compressor and gonna take the bad wheel bearing out. Hopefully no surprises!
  3. Stepside Billy

    What have you done to your square lately??

    Just drove home from work and feels like my front axle ate a bearing. Glad I'm off this week!
  4. Stepside Billy

    Frame welding

    Thanks Jerry, I appreciate the info.
  5. Stepside Billy

    Frame welding

    I'm gonna get a good welding blanket to cover it!
  6. Stepside Billy

    Frame welding

    Cool! I've never had to weld on my truck before!!
  7. Stepside Billy

    Frame welding

    I have to do some welding on my frame. Besides the battery, what should I disconnect before I do? Don't want to fry anything! Thanks!
  8. Stepside Billy

    Short Bed, Long Bed, Stepside Bed, Xcab Truck Bed !!!

    Like it or not, they did a hell of a job matching the lines of the cab!
  9. Stepside Billy

    What have you done to your square lately??

    Thanks for the info. I'll see if I can get the driveshaft with the axle.
  10. Stepside Billy

    What have you done to your square lately??

    I have been searching but haven't found the right answer. I know the 1 ton rear axles need the spring perches moved. Are the 3/4 tons bolt in? I have heard the front driveshaft may have to be lengthened
  11. Stepside Billy

    What have you done to your square lately??

    I found a couple of 14 bolts, just gotta save a few more pennies! Cheaper to buy axles than to re-gear. Besides, I'm up-grading from 10 bolt axles!
  12. Stepside Billy

    Leaking heater core?

    If it was the heater core you would smell anti-freeze in the truck.
  13. Stepside Billy

    What have you done to your square lately??

    Been driving her everyday. Picked up a Dana 44 with 4:10 gears today. Gotta find a 14 bolt with matching gears then I can swap out my axles with 3:08 gears. Should be an improvement!
  14. Stepside Billy

    What have you done to your square lately??

    Tightened up some belts and bumped the timing up 4*. Truck really liked it. Debating whether to go more.
  15. Stepside Billy

    Power seat wiring

    I'm getting a pair of seats from a Dodge mini-Van my brother is junking. The driver seat is power. What's the best way to wire it up? Should I run it straight of the battery or fuse box? I can get all the wire and connections out of the van. Thanks!
  16. Stepside Billy

    What to do? Repair shop f'ed up...

    Hey, that's real good to hear they stood up and took responsibility for what happened. That's a place to recommend to people!
  17. Stepside Billy

    What have you done to your square lately??

    It starts right back up with no problem. Mainly at lights or when I shift into gear. I have to feather the gas a little with my foot on the brake.
  18. Stepside Billy

    What have you done to your square lately??

    Trying to figure out my stalling problem. Once in a while the truck will just stall. No shaking, like I turned of the ignition. Replaced the IAC but still did it. Runs great though!
  19. Stepside Billy

    Help stop theft 87 V10

    I would think a quick release steering wheel would help. I don't think too many thieves have a spare steering wheel with them but then again....
  20. Stepside Billy

    How big of a camper can i install?

    Are you towing it or is it a slide in? You might need to add helper springs.
  21. Stepside Billy

    What have you done to your square lately??

    Set the timing finally. It was way off. Cap, rotor and wires next. Got the good brass cap!
  22. Stepside Billy

    What have you done to your square lately??

    Now that you mentioned it, I think you're right. I thought they were available for squares also. Someone else may know!
  23. Stepside Billy

    What have you done to your square lately??

    I have seen them. What I would love to find is the stepside fender that has the dimple to mount the spare on the side of the bed.
  24. Stepside Billy

    What have you done to your square lately??

    Wasn't too bad. I slid the bed back and the tank bolts pretty much snapped off. Worse thing was I put it back together, fired her up and had gas leaking from around the seal. Took the gas tank out again and reset the seal. This time I left the tank on my jack, hooked everything up and fired her...
  25. Stepside Billy

    What am I missing?

    Pulled the tank and reset the seal. Tested it BEFORE I bolted the gas tank up!

Latest posts

Forum statistics

Threads
45,581
Posts
986,832
Members
38,671
Latest member
Mavric16
Top