Search results

  1. D

    Interior Journal

    Good info, thank you. Luckily, so far anyway, all the welding I have to do except one small spot on the outside of the rocker will be hidden under carpet
  2. D

    Interior Journal

    Cab floor support is trash
  3. D

    Interior Journal

  4. D

    Interior Journal

    It doesn't look like the new pans will reach up that curve of the seat hump so I'll have to figure out what to do there Also, those little spot welds across the bottom of the door threshold are weird looking. It doesn't look factory to me but I've never gone this far into one of these things so...
  5. D

    Interior Journal

  6. D

    Interior Journal

    Cut out some of the rot today on the driver side. I have floor pans here, the rockers are on order from LMC. The rocker isn't as bad as I thought it'd be, just a small spot on the outside I cut out. The interior of the rocker doesn't ok great but I'll get a better look once the floor pan is...
  7. D

    77 K10 - what should I be asking for?

    Purchased for $3200 about 5 years ago Everything listed below has been performed by myself within last few years, with less than 500 miles driven since I've owned Complete rear-end rebuild, new bearings, ring and pinion and TruTrac with aftermarket different cover All brand new u joints All...
  8. D

    Interior Journal

    For some reason the driver side floor pan picture didn't upload, but it's the worst of it. There are several small chunks of metal completely missing and can see through.
  9. D

    Interior Journal

  10. D

    Interior Journal

  11. D

    Interior Journal

  12. D

    Interior Journal

    Starting on interior. Today I pulled the bench seat the floor matting and padding. Found a few ventilation holes in the floor pan. Looks like I am going to be learning how to weld
  13. D

    No power at all, zero lights, guage lights, or anything else. Any help wld be great.

    Did you install a shim on your starter? If so you may want to remove it and try again, sounds like the starter is too far away from the flywheel
  14. D

    Dakota Digital RTX Install Critique

    For future readers - water temp and tach both get fed thru the PF4 BMI and outputs directly into the DD gauges so no need to run the extra wiring. Only need to install the oil pressure sender and wiring Still trying to figure out how to get the GPS BMI to output correctly tho
  15. D

    Dakota Digital RTX Install Critique

    Finally started mine today after having it sitting in a box for almost 2 years. SquareRoot - what all did you NOT use on your setup because its already fed by the PF4 system? Coolant temp? Tach?
  16. D

    Wiring Harness? Choosing one?

    I went with the Painless kit myself when i did mine. The difference being the documentation and instructions in the book
  17. D

    K10 fuel line for Holley sniper truck has dual tanks but I’m buying the hokey tank with the efi fuel pump it I’m needing a line kit for just one tank

    I ended up buying pre-made length SS braided with AN fittings for the supply side. I ran the return in rubber fuel-injection rated hose
  18. D

    Dakota Digital RTX Install Critique

    Just future readers - i did ask, and they do not have anything other than the single BIM bracket
  19. D

    What aftermarket engine harness?

    I know there is a sort of block from the factory in that same location. Sorry, I'm not a ton of help. But there are some absolute geniuses here who know these trucks inside and out and they'll be able to help you
  20. D

    What aftermarket engine harness?

    Ok my painless kit, it came with a new fuse block. Power wire went from fuse block and then teed off there to catch there starter. I am not familiar much with the electrical and how it works - i just followed the instructions I will say that when I was researching which harness to buy, the...
  21. D

    What aftermarket engine harness?

    I used the Painless kit last year. Worked out well
  22. D

    Have you checked your ground?

    Good info - thank you
  23. D

    Have you checked your ground?

    I finished a re-wire of my 77 a few months back. One of the things I did was to completely create new grounding points with threaded studs and nuts/washers 1 - underneath bed between fuel tanks 1 - at rear fram 1 - at firewall, next to fuse block 1 - at driver side fender 1 - at driver side...
  24. D

    New wheels and tires for the 77

    Drivers side is before, passenger is after
  25. D

    Steering Column needs to be rebuild

    I rebuilt my 77 tilt column myself. It wasn't fun but I got it done. All new parts when available, including bearings and the little pivot ball thing. The worst part was that I had collapsed the little plastic shaft holders without realizing it, and it took forever to realize why the shaft...

Latest posts

Forum statistics

Threads
45,558
Posts
986,230
Members
38,644
Latest member
FenderBanger
Top