Search results

  1. GreaseDog

    Vortec with TBI?

    Carb intake will cost you EGR, and a custom tune is mandatory. You will love it though.
  2. GreaseDog

    upgrading your square with a hydraulic clutch

    Lol
  3. GreaseDog

    Using stock speedo VSS in place of transfer case output VSS?

    Got an 84 C10 that I'm planning on swapping onto a 4x4 chassis, I'll be using a 94 K3500 TBI harness to swap in the 80e. Originally transfer case in the donor had a VSS on the output shaft, this won't work with the stock speedo add it is cable driven. I've read somewhere before that you could...
  4. GreaseDog

    upgrading your square with a hydraulic clutch

    Thanks Richard! Lol
  5. GreaseDog

    upgrading your square with a hydraulic clutch

    Just came across some new information! Someone has taken the hydro pedals and dissected them, and adapted the measurements to a mechanical pedal. thanks go out to Josh Harmon(via Facebook) for the pedal modification information.
  6. GreaseDog

    auto locking hub to oem hub with NP203

    What you're not understanding is that converting to full time 4x4, is not going to make it handle like an audi. That lack of turning radius you didn't like in 4 high in your part time truck will be a constant lack of turning radius in a full time truck. Comparing a 40 year old truck to an...
  7. GreaseDog

    305TBI to 350TBI

    Twister, which crate engine are you looking at.
  8. GreaseDog

    305TBI to 350TBI

    My 94 has an L31 crate engine in it., fed by a modified stock throttle body. Performer RPM intake, adjustable fuel pressure regulator. It does require PCM tuning, but it's all worth it. So much more power than a stock L03 or L05.
  9. GreaseDog

    Going from Quadrajet to Edelbrock 600cfm

    A quality remanufactured QJet will not only run better, but it will not require any modification to install, and once it's set that's it, no need to mess with it ever again.
  10. GreaseDog

    NO OIL pressure

    Put a mechanical gauge on it and see what it says.
  11. GreaseDog

    Completed Project: Dual Fuel Gauges w/Tach

    Clean install Rich. Does that tach come with a wiring harness to run the tach?
  12. GreaseDog

    Vibration in square body driveline

    Check you ujoints.
  13. GreaseDog

    Axle + shackle flip

    If you have the 3 hole perches, move the center on to the front hole, you won't get a cleaner install than that.
  14. GreaseDog

    axles for sale

    I still have the front, but I'm planning on using it now. Rear is long gone.
  15. GreaseDog

    thinkin bout a motor swap..

    Just a heads up... Only the early ones..
  16. GreaseDog

    CB Radio Mounting

    :lol:
  17. GreaseDog

    1980 K10 Exhaust

    In that case, they're probably just going to look for a converter, muffler, and an intact AIR system if equipped. Pipe diameter and routing are probably not a concern.
  18. GreaseDog

    1980 K10 Exhaust

    Not sure why you want to go to a single 2.5" exhaust though. Any special reason?
  19. GreaseDog

    1980 K10 Exhaust

    He's looking for the part that has "NA" where the part number is on that diagram... That means it is not available. Try finding a Goerlich exhaust catalog, perhaps it will have it listed. Is it possible it's just a straight length of pipe? I don't see why the 117.5" chassis version, with a...
  20. GreaseDog

    Thumpr cams

    L79 cam seems to be the go to cam for high school rides. Lol that's what mine had in it. Milled 882 heads, 12cc pistons, worked QJet, Edelbrock intake, headers, 2500 stall in the TH350, and 3.08 gears. Would surprise many a Mustang and Camaro, and I was one of only a few in the parking lot...
  21. GreaseDog

    Thumpr cams

    The guy with a lower ,legit time slip on his dash where I come from.
  22. GreaseDog

    1988 bbc tbi power

    The Roush cars are actually fairly tame on the street for the power numbers. Go from a Stage 3 to a Shelby GT500... 662HP (only 100 more HP) goes from street friendly performance car to retarded power in a hurry.
  23. GreaseDog

    Need to extend?

    http://www.summitracing.com/search/make/chevrolet/year/1990/department/chassis-suspension/section/steering-components/part-type/steering-arms/amount-raised/4-000-in
  24. GreaseDog

    Rear Axle Bearing Play Some or None?

    That only works on a full floating axle, there is no adjustment for a semi floating rear axle. There should be a tiny bit of play, but too much could mean a worn differential cross shaft, or wear on the end of the axle shaft.
  25. GreaseDog

    Single Fill Dual tanks

    GM did not offer the solution, someone added it after the fact if that is how your tanks are plumbed. Nothing I've ever seen in any GM literature regarding this option, and I've seen this question pop up at least a dozen times over the last 15 years.

Latest posts

Forum statistics

Threads
45,558
Posts
986,228
Members
38,644
Latest member
FenderBanger
Top