Search results

  1. M

    81 K20 Pulling Right.

    They do if the alignment is fine and the ball joints are toast. That actually wouldn't surprise me at all! It sounds like it needs a full rebuild, but I suppose if the drag kink and tie rod were completely shot that might be it, but, they probably would have told you so. So Im guessing the...
  2. M

    New intake and carb question

    Why the wiper motor?
  3. M

    290hp 350 heads upgrade?

    The biggest gains were from the RV cam. The RV cam all by itself would have done the same thing for him.
  4. M

    RETRO-Mod: Jeep intermediate steering shaft

    Summit sells a double U joint slip shaft for our trucks for a reasonable price. Whether they fit right I dunno
  5. M

    New intake and carb question

    What intake and what carb are you putting on? post some pics
  6. M

    !!!!Need Np208 transfer case!!!!

    Ya its good you got it going for now but I would keep your eyes peeled for another case. It wont last for too long.
  7. M

    !!!!Need Np208 transfer case!!!!

    Ya I don't think either one will hold up for very long. I've seen guys try it before and it always just falls apart after a little while.
  8. M

    What have you done to your square lately??

    Did my pre winter tune up: Plugs, Cap & Rotor, Oil change and spray down the carb. I have put off the cap & rotor for way too long so I finally decided to replace them. I found that there was a slight oily residue all over the electronics, reluctor and springs. So I used Carb cleaner and...
  9. M

    !!!!Need Np208 transfer case!!!!

    You guys forget that it is aluminum and welding cast aluminum rarely if ever works out very well. I have seen that first hand several times. It has something to do with how the metal grain lays in cast aluminum and when you try welding it, it just doesn't stick together. You would probably have...
  10. M

    Need to replace crimped heater inlet hose

    Yep that is what I would do too!
  11. M

    Q jet choke has defected

    First thing I would do is get a flat head screw driver and a shop vac and clean that mess up on top of your engine! Holy freaks I can barely see your engine let alone anything else! Ya unless you can get that screw out, your looking at either a newer carb with electric choke or a new intake so...
  12. M

    REMOVE a leaf?? or, How to Lower a 4" lift to stock height

    Don't worry! he has and painted it too!
  13. M

    700R4 issues

    Did you hook up the TV cable and adjust it properly?
  14. M

    !!!!Need Np208 transfer case!!!!

    Im sure one of these guys can at the very least point you in the right direction :)
  15. M

    Possible tranny problems

    What ever ED! LOL Don't flush a tranny OMG LMAO I really cant stop laughing LMAO That is like the dumbest thing I've heard in a long long time!
  16. M

    !!!!Need Np208 transfer case!!!!

    HotRodPC
  17. M

    !!!!Need Np208 transfer case!!!!

    kleedus
  18. M

    Ford NP208 Interchange / 27 Spline Output Shaft Th400

    Check out my Pm I sent you. Usually the bus service is dirt cheap like Greyhound or something.
  19. M

    Possible tranny problems

    Did you correctly install the pick up tube from the filter? Did you buy the correct filter? What else did you do to the truck? Do you have the correct fluid in it? Don't buy this shit, for even one second, that putting new fluid in, wrecked your tranny! That is complete bullshit!
  20. M

    Possible tranny problems

    You obviously don't understand how to do a tranny flush then LOL. To do a flush you still have to drop the pan! OMG why would you do a flush just to leave the old filter and sludge in there ? WTF dude!!! You drop the pan, clean it, install a new filter and then fill with ATF. Then you can hook...
  21. M

    Ford NP208 Interchange / 27 Spline Output Shaft Th400

    Its too bad every one is so far apart otherwise I could hook you up. I know where there's a few kicking around.
  22. M

    Ford NP208 Interchange / 27 Spline Output Shaft Th400

    Where is Trafalgar ?
  23. M

    trouble running when warm

    Ya its only when you come to a stop in gear that it will die.
  24. M

    Ford NP208 Interchange / 27 Spline Output Shaft Th400

    Well at least you still have the proper input gear from it. So if you find any right hand drop 208 you could open it up and swap input gears if need be. Just would need to put new seals in. Heck the full rebuild kit, bearings and seals is like $125 so it might be worth going through the...
  25. M

    Possible tranny problems

    Ive heard that bullshit all my life and it is just that bullshit! Think about it. When ever the transmission is running, there is tranny fluid being sucked up from the pan and pumped through out all the various passages. So why would it change or hurt anything, to drop the pan change the filter...

Latest posts

Forum statistics

Threads
45,566
Posts
986,358
Members
38,654
Latest member
boarder421
Top