Search results

  1. randomTruckKid

    Rear axle not alligning?

    Nvm.
  2. randomTruckKid

    Rear axle not alligning?

    De lifting my c10, all I did was take out the lift blocks, but for some reason the allignment pins won't allighn. I can get one side on fine, but the other is off to the side by about an inch maybe 1/2 inch.
  3. randomTruckKid

    Brakes still dont work.

    Well if you haven't figured it out I'm a little stupid. Also thw awnser to my question is yes I should put the supposedly "broken" one in. Because it's not broken and works better than the other one. Who would've guessed....Not me.
  4. randomTruckKid

    Brakes still dont work.

    So should I try 1 last time with that new mc. Or should I exchange it for a new one. The brakes still suck but it is just barely good enough to drive. And I mean barely.
  5. randomTruckKid

    Cs130 altenator not working.. maybe?

    Alr so trying to out my solution in simplest terms. The activator wire from my painless harness kit was not supplying any sort of power(to the L port of the altenator) when the key was on. So in order to make a quick remedy to it i hooked the wire for the altenator (with resistor and...
  6. randomTruckKid

    Brakes still dont work.

    Okay cool I'll just keep some fluid on me while I drive. It leaks out the back a bit but I do have it overfilled.
  7. randomTruckKid

    Brakes still dont work.

    Odd question... brakes are ... sub optimal. But good enough to drive while being carefull. But the rubber seal on my master is on backwards. It actually seems to be the wrong one. I can't seem to find the correct one however. Could this be part of my issue? (I've got a replacement mc coming in...
  8. randomTruckKid

    Cs130 altenator not working.. maybe?

    No I didn't. I found a solution and now my altenator works correctly
  9. randomTruckKid

    Cs130 altenator not working.. maybe?

    Puting a wire between the switched power one (just before the resistor) and the battery made it work. Now It seems my white wire switch isn't working?
  10. randomTruckKid

    Brakes still dont work.

    I think bleeding. Started to work on it today. Just going to wait till Sunday when I have help
  11. randomTruckKid

    Brakes still dont work.

  12. randomTruckKid

    Cs130 altenator not working.. maybe?

    I was asking on how to make it work.
  13. randomTruckKid

    Cs130 altenator not working.. maybe?

    Just did. No change. It actually dropped.
  14. randomTruckKid

    Cs130 altenator not working.. maybe?

    So my altenator hasn't been working.. or at least the voltage kn my gauge dosnt go up since I rebuilt my truck. I haven't gotten around to much addressing the issue due to other things like brakes. It's a cs130 altenator. And I re wired with a painless kit. The altenator is also brand new...
  15. randomTruckKid

    Brakes still dont work.

    This one dosnt go to the floor like the other one. It gets most of the way there then gets super stiff and I have to push super had and it slowly goes down. Don't think do?
  16. randomTruckKid

    Brakes still dont work.

    What.
  17. randomTruckKid

    Brakes still dont work.

    Here is video of goose sound
  18. randomTruckKid

    Brakes still dont work.

    Just kinda at the end of the stroke. It kina weezes or makes a goose sound. I can't hear it when the truck is on but I'm shure it's there. Both masters did it.
  19. randomTruckKid

    Brakes still dont work.

    Yall know how to get the master to stop making the goose sound at the end of the stroke. The other one did it too.
  20. randomTruckKid

    Brakes still dont work.

    55 and below for me...I freeze very easily. It currently 40. With a feels like of 19.
  21. randomTruckKid

    Brakes still dont work.

    Nvm. Old master = good. I haven't even bled the lines but I needed to get the tuck in the garage (it's freezing) and it stops better than woth the other matser However my truck REALLY does not like the cold
  22. randomTruckKid

    Brakes still dont work.

    Original mc is also shot. For other reasons.
  23. randomTruckKid

    Just want to make shure im reinstalling new control arms correctly.

    No. The springs will eventually settle. Idk how much height you will loose. And yes. You will need to take some shims out of the upper. Take the truck to a alignment shop. They will get it allighed for steering and with that.
  24. randomTruckKid

    Brakes still dont work.

    Helped a little but the brakes are still very squishy. Just going to put the old master on. The current one still makes a goose sound
  25. randomTruckKid

    Just want to make shure im reinstalling new control arms correctly.

    Turned in which way? You have to adjust your shims.

Latest posts

Forum statistics

Threads
45,562
Posts
986,306
Members
38,647
Latest member
rumph13
Top