Search results
-
What have you done to your square lately??
Looks like I need to push her outside and do some wash down. -
What have you done to your square lately??
@GXPWeasel @Poppy 87 Here's how I removed and reinstalled my bed. It may take a couple of tries to get center but once you do you can remove it by yourself. The last picture is important you need a gap so once you pull all your bolts slip a 2x4 or something between the frame and bed so you... -
What have you done to your square lately??
I will take some tomorrow, moving cows today. It's already set up just need to attach the chains. -
Mutha trucking Vintage Air
Watching this thread let us know how the install goes! I'm going that way also and curious! -
What have you done to your square lately??
I put some eye bolts in the 4 of the bed mount locations and used the engine hoist made it super easy to remove and re-install -
Crazy question
It's only 20 bolts and do able for cheap! Sorry I didn't read the whole post. The only reason to remove the bed bolts would be to give you access to the five bolts on each side and ten bolts along the bottom. Also to insert the front body panel. I think it can be done without removing the whole...- hoagster
- Post #24
- Forum: Paint and Body
-
!977 K10 Bedsides
Purchased new from Auto Metal Direct, and if you have to patient not every bolt hole lines up and just for the front panel there are 20 bolts. Is it hard no just time consuming and frustrating getting it lined up and square.- hoagster
- Post #11
- Forum: Paint and Body
-
Burnouts with a NP203 full time 4wd?
I did a four wheel burnout with my first square, it was a 73 not the one I'm working on it had a 396 in it. I promptly got pulled over and issued a hefty ticket. That was a long time ago while I was in H.S. which I graduated in 77. No need to do a burn out. Go dig some holes with it in the woods.- hoagster
- Post #12
- Forum: Transfer Case
-
What have you done to your square lately??
Repaired my old 40lb blaster, tested it out on one side of my passenger side door. Finished the down to the metal with my favorite tool. Cleaned it then rattle caned it. Still need to fix all the mirror mounting spots over the years. And blast the other side. -
Where do these wires go?
If you got this far, go do a lookup on a Massey 135 diesel tractor wiring diagram! My guess is Key on, and a relay which will allow the starter to function if all the safety measures are met.- hoagster
- Post #3
- Forum: Electrical & Audio
-
What new tools have you got lately?
New to me 2005 7hp 60 gallon Maxus Air compressor. Installed in the barn. Only a single stage have to be patient using the Blaster but it will work better than my old tired 1960's compressor. -
What have you done to your square lately??
It's going to be a daily driver, not a show truck. That said every nut and bolt has been removed and everything has been either rebuilt or replaced. Doing body work now to fix the minor rust on the cab. Not full resto, I'm guessing you'd call it a full resto mod? -
What have you done to your square lately??
Ask me that when I get done with my project! I got to drive it in High school, broke a few things back then and can't wait to drive it again. -
What have you done to your square lately??
who did you get that from and will it fit a Dana 44, looks like yours is a 60? -
What have you done to your square lately??
Worked on the front lighting harness which also has wipers, horn and brake pressure. So for those that have dealt with the wire going to the proportionate valve how was it routed and why do I have two splices, connections. The wiring diagram shows one plug (highlighted) I have an extra as seen... -
Yeah my posts are too long, but... this truck...
Nice, Welcome!- hoagster
- Post #15
- Forum: Introduction
-
my whacked column rebuild
Interesting my truck is a 73 k10 and I can't start it with the key, I can turn the truck on i.e. have power but can't start the truck. I had to wire in a push button and bypass the that portion of the starting system. Thank you, I have the steering column out I'm going to investigate it and see...- hoagster
- Post #54
- Forum: Suspension, Steering & Brakes
-
What have you done to your square lately??
Nice burb looks like my 94! -
What have you done to your square lately??
Save yourself some heart ache and get a impact driver also to press out and in the old and new parts. -
What have you done to your square lately??
Worked on cleaning up the rear lighting harness. Next up going forward to the rest of the lighting harness. Painless wiring products, get the tools, makes it easier! -
What have you done to your square lately??
I need a custom10 badge when you do!!! Can't find those anywhere -
What have you done to your square lately??
I Had an issue were everything would work fine, on my 94 suburban 2500hd, 454cid 4l80e, get done moving stuff driving around shut her down and it would puke fluid. couldn't find out were. I finally found a mud dauber hornet had plugged the vent line. it has been working fine since I cleared...