Search results

  1. Edelbrock

    NO power when key is in acc or on position

    Fusible link?
  2. Edelbrock

    Rebuilding rear axle DIY?

    From my limited understanding, you have to know EXACTLY how to do it. Any mistakes at all are not tolerable. There are enough important steps to follow that I didn't even bother finishing the rest of the "how to" video. No way would I even try it, but that's just me.
  3. Edelbrock

    Factory tach wire hole in firwall

    Well, that's up to you. I generally look for an exhausting hole that was put there by the factory to feed wires or linkages through the firewall. The the tach wire and be inserted through the existing hole. Wiring harness, steering shaft, throttle, etc. A drill works, or even a punch and sledge...
  4. Edelbrock

    4:10 gears for 86 k10

    Nice links.
  5. Edelbrock

    C10 LS Swap Actual Cold Air Intake

    Nice work man. Your hired! The only things I might look at is matching the ducting diameters, h20 drain tube in the bottom of the air box, putting an oiled foam cone over the filter (or just switching to a paper filter), and maybe insulating the air box and ducting so that the radiator heat...
  6. Edelbrock

    4:10 gears for 86 k10

    You installing a locking diff? If it were me, I would just get a complete junk yard axle that has a factory LSD. Is your rig a 4x4?
  7. Edelbrock

    Shift linkage problems

    I assume that you are pulling the shifter towards you when trying to get from D to P, yes?
  8. Edelbrock

    HIT THE IGN. KEY AND NOTHING

    Good to know.
  9. Edelbrock

    HIT THE IGN. KEY AND NOTHING

    I had a guy complaining that "the car works sometimes but not other times.... sometimes the car wont turn on". But I tried starting it like 50 times over the course of a few weeks. It ALWAYS started for me, and the other guy continued to have problems with it. He would get stuck in parking lots...
  10. Edelbrock

    HIT THE IGN. KEY AND NOTHING

    If you just need a quick workaround, you can buy one of these or make one. Its just a way to manually activate the starter. On the solenoid - clip one onto the S and one on the B. Press the button and the starter kicks on.
  11. Edelbrock

    HIT THE IGN. KEY AND NOTHING

    Assuming its an automatic, try holding the key in the start position when moving the gear selector from P or L and back. The neutral safety switch might be misaligned, and this would identify that issue. The truck should start in P or N, but if its misaligned, it might start in R or D, etc.
  12. Edelbrock

    Will a 8.5 Camaro 10 bolt axle fit in a 1981 squarebody?

    If you are replacing the entire axle, I don't see how splines would matter. As long as the drive shaft will bolt up to the U-joint, then what difference would the splines make? Note: I am no axle expert by any means.
  13. Edelbrock

    backfire under wide open throttle

    One thing you could try, would be to close the choke part way and see if the problem goes away. If that solves the issue, then your running lean without the choke. If it were me, I would try replacing the carb with a cheap one from Marketplace or Craigs.
  14. Edelbrock

    Will a 8.5 Camaro 10 bolt axle fit in a 1981 squarebody?

    Is your truck a 4x4? If so, that axle wont work unless you swap the front axle as well. The gearing will be different, so keep that in mind. I believe that the 4.11 gearing would give a lower top speed. If the length of the axle is wrong, you can use wheel spacers or different wheel offsets to...
  15. Edelbrock

    Toe adjustment 1987 V10

    All good info. Let the reader take what they can from whats posted.
  16. Edelbrock

    Toe adjustment 1987 V10

    Ya, if you can verify that two tape measures read 100% the same, you could use two different tapes. But any time the tape retracts and "slaps" back, you would need to re-verify the accuracy between the two. I have always used one and it worked well for me.
  17. Edelbrock

    Toe adjustment 1987 V10

    I do not recommend using 2 different tape measures. Use 1 tape measure to check both sides. Less variables this way. More accuracy. The rivets can loosen, the clasp at the end can have different bend angles, etc. The printed marks are always perfect, but the ends are always different. If...
  18. Edelbrock

    New whitewalls

  19. Edelbrock

    Computerized carb

    Whats a computerized carb? Do you mean throttle body fuel injection? Technically yes, you can put a carb on any engine. You could put a carburetor on a diesel engine. It just depends on how many mods you want to do.
  20. Edelbrock

    Searching for My Dad's 1979 Chevy Suburban

    Option number 2: Have a minor, or a street bum put up a $250,000 cash reward for the location of the vehicle. They can not be successfully sued, so what do ya got to lose?
  21. Edelbrock

    Searching for My Dad's 1979 Chevy Suburban

    Does West Deptford NJ allow the records to be pulled?
  22. Edelbrock

    Fuel pump

    When its hard to start, give it a shot of fuel or starting fluid. If that makes it start right up, then you are lacking fuel. If it makes it worse, you were already flooded.
  23. Edelbrock

    Toe adjustment 1987 V10

    You can basically just lean a board up against the front tire, and use a tape measure - like this: (Use one tape measure, not 2).
  24. Edelbrock

    New whitewalls

    Nice tires. I have seen worse....
  25. Edelbrock

    O2 Sensor

    Maybe install an O2 sensor that comes from the factory with a heating circuit? So the sensor heats itself up on its own. You would have to get one that has the same performance values though.

Latest posts

Forum statistics

Threads
45,562
Posts
986,306
Members
38,647
Latest member
rumph13
Top