Search results

  1. Strick

    Cracked TH350 case

    I'd replace the case. Just went thru this with my SIL's 86 TH400. HS
  2. Strick

    V2500 frame compatibility and advice.

    I have a very good 91 V1500 Sub body & chassis if you're interested. There should be no frame difference between the 1500 & 2500 & if so it's minimal. HS
  3. Strick

    New member with a new C10 build

    Thanks.Dad bought that 79 new in Benson, NC from Barnes & Lee Chevrolet. NC
  4. Strick

    New member with a new C10 build

    Welcome from Central NC. I love the color combination and year... HS
  5. Strick

    Time to say hi from Husker Country.

    Welcome from the Tarheel State. It's tough to drive them & work on them simultaneously but we do what we must! I drove my 72 Camaro in primer for years (10) until I found time & funding to paint it. Good luck with your project! HS
  6. Strick

    intro and advice

    Man, what an intro. I hate it for you. There are plenty of Sub folks here that I'm certain would be interested in what you're offering.
  7. Strick

    90 burb, New motor, water pump, overheating only when t stat is installed

    Make certain that the belt routing & fan blade orientation is correct. Make certain that there's correct tension on the belt as well. I ran into a similar issue with an old NC Forestry K2500 years back. HS
  8. Strick

    New to this here forum

    Welcome from NC. HS
  9. Strick

    What have you done to your square lately??

    I worked on my '87 & it's not perfect but it's good! Considering it was almost 40 years old with mostly original paint, I've given the next owner a much better guide coat than what I started with. Your ride looks great, put the adornments back on & go ride! HS
  10. Strick

    Custom drive shaft.

    The slip yoke should be half it's travel with the vehicle suspension supporting the sprung weight. HS
  11. Strick

    Hello new member from central North Carolina

    Welcome from Central NC. Seems you'll need an aftermarket intake so you can 4bbl that 94 engine. Make sure it has the 168 tooth flexplate as well so it couples to your converter & starter. Keep asking questions and look at the posted forums for help also. HS
  12. Strick

    87' a/c brackets

    I believe that it's have a complete set on a radial compressor. I'll check later for you. HS
  13. Strick

    New Guy

    Welcome from the Tarheel State. Is the K20 a 4 speed manual? Low miles & almost 40 years old means it must be in good shape. Share some pics. HS
  14. Strick

    New to the forum

    Welcome from Central NC. I love that CUCV as I've had a few myself. Love to have that 8274 too...mine went with my last M1008. HS
  15. Strick

    Howdy from Poland

    Welcome from the Right Coast here in Central NC. Nice score on the K20, especially with the 4-speed. HS
  16. Strick

    New to the page

    Thanks man. My dad bought it new in 1979. HS
  17. Strick

    New to the Forum

    Welcome from Central NC, dig the right & thank you for your service! HS
  18. Strick

    New to the page

    Welcome from the Tarheel State Waterboy. That a high quality R-3-0 you have there. I have a pair of 79 Crews myself. HS
  19. Strick

    1987 Chevy V10 steering wander

    @idahovette beat you to it. I should have misspelled AXLE to get @SquareRoot involved too!
  20. Strick

    1987 Chevy V10 steering wander

    Thanks man!
  21. Strick

    1987 Chevy V10 steering wander

    You are so right. I just looked at the message and saw the error of my ways. Good catch and call out. I had 40 hours of work this week thus far and between those and the birthdays it must be messing with me... Strugglin'
  22. Strick

    Introduction and BBC to SBC???

    Welcome from Central NC. Does your big iron have the radial or axial compressor on it? The radial is the smaller pancake style and axial is the longer and was used on BBC trucks right on through the late eighties on most. HS
  23. Strick

    1987 Chevy V10 steering wander

    The caster can be adjusted as well but it is an extreme pain in the arse! You have the break the wheel end of the axle all the way down to the knuckle and install shims between the spindle and knuckle. I have replaced ball joints on 10 bolts and Dana 44's and have seen some of these shims in...
  24. Strick

    What have you done to your square lately??

    I finally got another opportunity to work on the '87 again. I got more than half the body molding done. HS
  25. Strick

    NOG Here

    Welcome from the Tarheel State. HS

Latest posts

Forum statistics

Threads
45,562
Posts
986,278
Members
38,645
Latest member
sallyjeank10
Top