Search results
-
Door wiring conduits
I did this. the only problem I had was having the balls to drill a hole in a perfectly good cab. -
Bed mounting hardware for short box step side.
I think i got all my hardware from Classic Parts.com. Wood, stainless strips, hardware,tailgate chains- Ken B
- Post #6
- Forum: Paint and Body
-
Help with gauge cluster lights
I replaced most bulbs with LEDs. But not all it would been too bright- Ken B
- Post #10
- Forum: Electrical & Audio
-
-
New to forum
Welcome . the knowledge in here has absolutely made it possible for me to get to the point that I am looking to get paint going. Without the knowledge in here I would be sitting in the middle of a pile of parts.- Ken B
- Post #2
- Forum: Introduction
-
Oh My What has Easton Bought Now
Good Luck to you both. A burb to me means MORE work more parts to replace.- Ken B
- Post #2
- Forum: Other Vehicles
-
-
-
Step Side Bed Wiring
thanks guys. all good info and open to other ideas- Ken B
- Post #5
- Forum: Electrical & Audio
-
Step Side Bed Wiring
Keith I have grounded from the mounting bolts on the lights to the frame in the past. just trying to not have extra wires hanging out there.- Ken B
- Post #4
- Forum: Electrical & Audio
-
Step Side Bed Wiring
I am seeking advice .....I am trying to get a good ground on the back of my step side bed and I came up with this.... upside,downside, completely wrong???? The pic was taken from the ground looking up used a body bolt and connected ground strap to bed and the other end to the frame. I have had...- Ken B
- Thread
- Replies: 9
- Forum: Electrical & Audio
-
Air Cleaner Stud
surfing thru here you find parts #s faster than some of the parts houses....WFarm thanks. was thinking about that rod and poof you already had the part #. thanks- Ken B
- Post #11
- Forum: Engine & Performance
-
-
What are these holes for?
Is there anyone who replaced inner fenders and "plugged" the unused holes. the fenders have extra holes for jack/lug wrench and other things I am sure. Anyone find a way to plug these unused holes? thinking small rubber grommets?- Ken B
- Post #6
- Forum: Paint and Body
-
Finally, a squarebody forum!
Welcome from Indy....volumes of great information here Very helpful members- Ken B
- Post #5
- Forum: Introduction
-
-
-
USA1 Seat Belt Set - NEW - Charcoal
I will start by saying very satisfied with usa1 products but 16months for door panels....sheesh -
Emmissions and Vacuum Routing Help
1 down.....thanks I will cap it .- Ken B
- Post #3
- Forum: Engine & Performance
-
Emmissions and Vacuum Routing Help
Gentlemen, I am looking for Vehicle EMission Information and Vacuum hose schematic for my project. I have a Rochester quadrajet t4 478 carburetor and included a pic of the engine casting #. There IS a smog pump on the engine. I have a donor motor and I am looking for the routing for the vacuum...- Ken B
- Thread
- Replies: 3
- Forum: Engine & Performance
-
OEM Breather replacement
But maybe I got a part # out of this thread.....hahahaha thanks Goldie -
Has anyone weighed a 15x8 rally wheel
Excuse my naivete(AKA inexperience) why would the weight of a steel rim on a big steel block you are driving down the road matter? Racing I get ..truck rim?- Ken B
- Post #11
- Forum: Wheels and Tires
-
Steering Wheel Cleaning
thanks , will try to scrub and see how it turns out. -
Steering Wheel Cleaning
How do you get 40+ years of gunk off of a steering wheel? -
fuel venting
I think I have all of the lines for vapor capture done , except 1....the line with green tape at the canister and another green tape near the other end. where does this connect. Didnt know if a carb pic would be helpful , there is a hose plugged with a screw that I need to figure out...unless...- Ken B
- Post #22
- Forum: Tech Discussion
