Search results

  1. Dmack

    Fuel Tank Selector Valve Leaking

    Not sure why someone said they aren't made anymore. It is the standard six port with the five wire harness connector. I put a new one in last month from napa.
  2. Dmack

    Fuel Tank Selector Valve Leaking

    IIRC, that is a vent for the valve. If it is leaking, the valve needs to be replaced.
  3. Dmack

    New steering column

    If you get one from a similar year truck (not column mounted wiper or dimmer switch, for example), it should be a direct bolt in and pinout.
  4. Dmack

    Sm465 not shifting

    Yes on pulling the trans to swap the throwout bearing, unfortunately.
  5. Dmack

    Is my transmission going out?

    Choke stuck on?
  6. Dmack

    Bed tie downs?

    I use eye bolts on all four corners and one both front and back of the inner fenderwells. Handles all tie down issues I have found.
  7. Dmack

    Snow tires for lifted trucks

    I put these on my Dodge and they handled great in the snow. I recommend them highly. LT285\70R17.
  8. Dmack

    4WD Wheel & Tire Thread

    4" lift, 16x8 wheels, zero offset, lt315\75r16 AT tires
  9. Dmack

    8 MPG?

    Interesting. My 83 K20 has a 14ff. Assumed it was original, but not sure now.
  10. Dmack

    8 MPG?

    Sounds about right. Mine is similar - factory crate 350, 4 speed, 4.11 gears, 4" lift, 35's. I get 10 with mostly in town driving.
  11. Dmack

    New and a load of help needed

    Welcome. Some pictures of the lines and wires you are asking about would help. Also, if you are talking about vac lines off the carb, the make\model of the carb and a pic would help too.
  12. Dmack

    1984 k20 question

    http://www.offroaddesign.com/catalog/Transfer%20Case%20ID%20Guide.htm Here is a quick comparison between the 203 and 205. I would think it should have either 4 or 5 positions. Can't think what would have 3.
  13. Dmack

    Fuel gauge

    Where is the needle pointing? 3 o'clock is an open circuit (like a broken wire or connection) and 9 o'clock is a grounded circuit.
  14. Dmack

    Does my engine have a chance of living?

    Ok, I have heard this before and have a question. If you swap in a high volume pump, since the internal resistance stays the same (bearings, etc), won't you naturally have higher pressure? Therefore higher volume pump equals higher pressure pump in a given engine.
  15. Dmack

    Tail light screws 1980?

    Of you could just go to a local hardware store. IIRC, they are #8x1" .
  16. Dmack

    Fuel Gauge

    The best way to test the sender wire is with an ohm meter. Unplug the wire at the sending unit and put one meter lead on the post and the other to ground. You should get a reading between 0-90 ohms. If not, you have a bad sending . Then put one lead at each end of the wire and you should get...
  17. Dmack

    What would cause the gas gauge to peg past full?

    Think of the single post on top as the positive and the wire coming off the housing is the negative.
  18. Dmack

    Fuel gauge

    I just corrected my above post as I had it backwards. Sorry for any confusion.
  19. Dmack

    Fuel gauge

    Where does your gauge point? 3 o'clock is an open circuit (broken wire/connection) and 9 o'clock is a grounded out unit.
  20. Dmack

    Tailgate help

    The one I pulled was held on with double sided foam tape, like they use for trim. Reinstalled it with the same and seems to work fine.
  21. Dmack

    What have you done to your square lately??

    Added a headache rack, just because. Replaced the fuel switching valve and headlight switch since I was having trouble with both.
  22. Dmack

    Can you change the fan speed switch to a dial switch?

    Mine has a stripped out A.C. factory system. I just pulled a factory non- AC control panel, cables, and inside plenum as a full unit. Actually easy to swap out . And you can use all of the original wiring.
  23. Dmack

    Let’s see your bumper

    Made mine from scrap. More fun than buying a premade one.
  24. Dmack

    99 -06 GMT 800 NBS seats in a Square Body C10

    Looks good. Let us know how they feel while driving.
  25. Dmack

    White spots?

    Just a guess, but it looks like your clear coat is failing. If that is the case, you can't buff or sand it out. Paint guys (not me) may have some suggestions.

Latest posts

Forum statistics

Threads
48,673
Posts
1,074,341
Members
43,349
Latest member
samelthecamel19
Top