Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Dmack
Full Access Member
·
From
Central OR
Joined
Mar 13, 2019
Last seen
Yesterday at 6:02 PM
Posts
320
Reaction score
403
Points
63
Find
Find content
Find all content by Dmack
Find all threads by Dmack
Latest activity
Postings
About
Dmack
replied to the thread
New carb starts then dies after 5 seconds
.
Make sure your idle mixture screws are out about 1.5 turns each, not run all the way in. With the engine off, cycle the throttle...
Jul 14, 2024
Dmack
replied to the thread
Steering shaft
.
The plastic pins are put in at the factory to hold length until a collision, where the impact will push the shaft into itself, instead...
Jul 7, 2024
Dmack
replied to the thread
Steering shaft
.
You can heat them, drill them, or just hit it hard. I was able to install mine by lining it up just right and prying it in. Make sure...
Jul 7, 2024
Dmack
replied to the thread
Fuel gauge
.
Past full means open circuit (ie broken/disconnected wire.
Jun 29, 2024
Dmack
replied to the thread
Steering Box Question
.
I believe they will bolt in, but hopefully you can find someone to respond who knows for sure. I swapped the crossmember from an 84...
Jun 26, 2024
Dmack
reacted to
89Suburban's post
in the thread
What new tools have you got lately?
with
Like
.
Love mine. Had mine about 10 years now doing all my own tires and some relatives here and there.
Jun 7, 2024
Dmack
reacted to
Frankenchevy's post
in the thread
Any Tricks for stuck oil filter ?
with
Like
.
I have a rubber strap wrench that I typically try first if my hand doesn’t work. Otherwise, I have a wrench from harbor freight that has...
Jun 4, 2024
Dmack
replied to the thread
My wife is small and is pregnant
.
Look up running boards or tube steps. There have been lots of variations over the years.
Jun 3, 2024
Dmack
replied to the thread
Brakes locking up
.
Pushrod isn't adjustable on mine with the hydroboost. Fought the lock up issue for a while before trying this. Haven't had the issue...
May 13, 2024
Dmack
replied to the thread
1972 GMC C10
.
The automatic will roll in any gear shift position except park if it's not running. On the shifter not going into park, try dropping...
May 13, 2024
Dmack
replied to the thread
Brakes locking up
.
I had the same occasional problem on my 83 that had been converted from diesel to gas. Still.has the hydroboost. Bleeder test would...
May 13, 2024
Loading…
Loading…
Latest posts
12 bolt didferential gear ratio identification
Latest: RetroC10Sport
Today at 12:41 AM
Auto Accessories Garage
C
Wheel spacer for my 1986 GMC K3500 3+3….
Latest: CalSgt
Today at 12:39 AM
Wheels and Tires
gear ratio
Latest: RetroC10Sport
Today at 12:39 AM
Differential & Driveline
I
Anyone running an 8.1, what trans are you using?
Latest: IDtag
Yesterday at 11:54 PM
Automatic Transmission
It has a voice....
Latest: SquareRoot
Yesterday at 11:49 PM
Electrical & Audio
Forum statistics
Threads
43,044
Posts
927,227
Members
34,640
Latest member
Crick13
Members
Top