Search results

  1. Dmack

    Truck left me stranded today.

    Don't forget the filter in the inlet of the carb.
  2. Dmack

    Favorite Project Truck Sales Pitches

    Drove 4 hours to look at a 69 C10. Was told "engine runs strong". As I drove up, I could see the starter hanging just off the ground by the main wire. Popped the hood and the heads and intake were missing. I said "runs strong"? He says "well, it will once you put it together".
  3. Dmack

    Compressor overload keeps tripping

    Make sure you are getting 110v to both legs, not just one.
  4. Dmack

    Help with fuel guage problems

    The general rule is if it reads below empty (9 oclock) the unit is grounded out. If it reads last full (3 oclock), it is an open circuit.
  5. Dmack

    700R4 Spews fluid when in reverse.

    Necropost
  6. Dmack

    Oil pressure question… or two questions

    You are assuming the factory gauge and sender areaccurate. After changing the sender in mine twice, I put a mechanical gauge in it. Gm crate engine with unknown miles and maintenance. 40 on cold startup and 30 warm.
  7. Dmack

    Fuel gauge repair HELP

    Sounds like it. That shows the gauge is working, and tells me the wiring is good. I have had several bad sending units with open circuits over the years.
  8. Dmack

    Fuel gauge repair HELP

    Past full means you have an open circuit. Usually means a bad connection, broken wire, or bad sending unit. Needle past empty is grounded.
  9. Dmack

    DIY Raptor Bed-liner

    I used on mine about 3 years ago. Overall, I'm happy with it. Looks good, but longevity isn't anywhere near the commercial jobs. The raptor will scrape off if I drag a piece of metal with any sharp edge. I also slide 25gal propane tanks over the tailgate and it will wear through.
  10. Dmack

    Mounting tires at home

    Thanks for the link. Looks like a decent design other then the flimsy bar. May have to do some experimenting. My current project is a 1970 C20 I have swapped an 84 C10's running gear into. I have some used BFG 31's in going to mount on the ralleys.
  11. Dmack

    Radiator removal

    You will need to pull the fan first. Once out, I pull the staples and replace them with two 5\16" x1" bolts so you can easily pull the top separately in the future. Comes in handy when working on the belts, changing ps pump, water pump, etc. And welcome.
  12. Dmack

    Mounting tires at home

    If you get a chance, I would like to see a pic of a bar that actually works. Thanks
  13. Dmack

    CA legal LS swap

    Nice write up. Makes for one more reason I'm glad I don't live there .
  14. Dmack

    Bed liner yes or no

    I have a 99 Dodge Cummins, a 50 Ford F1, my 83 Square, and my newest project, a 1970 Chevy C20. I don't discriminate by brand.
  15. Dmack

    Bed liner yes or no

    I used it in my 83. Looks good, very grippy, but not nearly as heavy or rugged as the commercial spray in types. Of course, it only cost me $50, as opposed to $400+ for a commercial job. I have a rubber mat in my Dodge, and that would still be my first choice.
  16. Dmack

    Going price for 8' beds

    I just parted out an 84 to use in my 70. Box was rough and couldn't get a call at $75. Ended up pulling it apart to keep the near perfect floor. Cut a filler door for TheFishBox 's project, and scrapped the rest. Finally got $50 for a good cab and frame.
  17. Dmack

    TH350 Slips in Drive but will back up

    I think they take up to 10 quarts if the converter was drained also. Just agreeing 4 may not have been enough.
  18. Dmack

    Hypothetical SBC question

    Granville King was the author, IIRC. Either 4 Wheeler or 4 Wheel and Off Road mag. Used to subscribe to both I high school. You remember when there was no interweb and you actually had to look at books and magazines for info?
  19. Dmack

    TH350C been sitting a few years

    Thanks for the help.
  20. Dmack

    TH350C been sitting a few years

    Matt69olds, can you recommend a rebuild kit for the TH350 for just average use, not high hp applications? Thinking about trying it on a spare th350 I may put in my new 1970C20 project. Not trying to hijack the thread, but thought it was relevant. Thanks for the help you routinely give here.
  21. Dmack

    12valve/nv4500 into 79’ K30

    We needed a new engine in a car at work years ago. Local shop that we used quotes $4100 for a sbc (just the engine, no labor). I told our lot guy that was high and to call and see what the local chevy dealer wanted for a new factory long block. They say $2400. He says "great, can we order...
  22. Dmack

    black vinyl cover for off road light

    Did KC make an 8" ? I just remember their 6" .
  23. Dmack

    What have you done to your square lately??

    You have much better technique than me then. I bought a new windshield for $110 delivered to my local LKQ. Took a friend and I about 30-40 minutes to install it. I then spent 45 minutes getting about 16" of the lockstrip installed. Finally gave up and ordered the tool. When it arrived , I...
  24. Dmack

    Dually door interchange ?

    Should be. The burb kept the same body through 91, where the trucks stopped in 87.
  25. Dmack

    Instrument gauge cluster bulb replacement.. now no left turn lights?

    As stated above, led bulbs can be polarity sensitive. Also, I believe some take a special led flasher unit.

Latest posts

Forum statistics

Threads
48,673
Posts
1,074,336
Members
43,347
Latest member
mo4154
Top