Search results

  1. gilby959798

    Tremec TR-4050 swap

    I did this a couple of years ago but my truck is not close enough to purchase yet.
  2. gilby959798

    Tremec TR-4050 swap

    Honestly with my 4.56s I would prefer a different 1st and 5th gear set. Give me something that I can actually use 1st and something that makes 5th like 2k RPMs with 33s.
  3. gilby959798

    Tremec TR-4050 swap

    I am really looking forward to the progress since I am a few months behind you. When I got a quote for it, it was just under $5k. Do you mind saying what your quote was?
  4. gilby959798

    Time to sort out Dad's old truck!

    Welcome, looking forward to seeing the progress as I am in the middle of a much bigger project so those who continue to get them looking nice keep me motivated to get there some day.
  5. gilby959798

    FOUND - Digital Dakota Gear Indicator Cover

    If you don't find what you're looking for let me know. I make these that go in that location. For the factory clusters, the original lighting lights up the ones with the see through.
  6. gilby959798

    What have you done to your square lately??

    My life lately consists of cut, grind, weld... rinse and repeat. This was my attempt of doing this one myself since the firewall was replaced and it was not quite the same as the original.
  7. gilby959798

    Tremec TR-4050 swap

    But I already have the ancient T case LOL. I know I will be bale to fab something up for the shifter.
  8. gilby959798

    Tremec TR-4050 swap

    The quote i got said it had an adapter to a 10 spline t case input shaft
  9. gilby959798

    Tremec TR-4050 swap

    I plan to order one at the beginning of the year (hopefully) if I get the body work where I want it, along with a 383. What T case do you have currently?
  10. gilby959798

    What have you done to your square lately??

    Ok I'm talking to my buddy, he can make them for me after I test the 3d print. I was thinking about making 5 to start off with.
  11. gilby959798

    What have you done to your square lately??

    Please note, I changed the shifter rails for this project as well They might not look that different but the notches on the right shaft are deeper in the 4WD positions than the shaft I took out. I'm not sure it'll work if you don't have a newer shaft.
  12. gilby959798

    What have you done to your square lately??

    Went through the transfer case over the weekend I plan to put the 4wd indicator light in it but finding the sensor that fits is next to impossible so I designed my own adapter to use a typical back up light switch and then 3d printed it for testing before having one made. Slowly but...
  13. gilby959798

    C10 Fall Revival 2025, Denton, NC

    Trying to knock some stuff out this weekend!
  14. gilby959798

    C10 Fall Revival 2025, Denton, NC

    I just hope I can get my truck out there next year :rolleyes:
  15. gilby959798

    C10 Fall Revival 2025, Denton, NC

    Planning on a seat similar to this. I love the topper on this.
  16. gilby959798

    C10 Fall Revival 2025, Denton, NC

    I am likely flying solo, so if any of y'all want to meet up, send me a message to exchange contact info.
  17. gilby959798

    LED headlight upgrade

    I love my Hella lights in both the square which is not drivable and 67 Mustang which is.
  18. gilby959798

    What have you done to your square lately??

    Cut out the bad Added some good Fully welded this section in Made a panel to fix the other portion of the firewall. The plan is to make it look smooth, minus the flanges for the outside cowl panels
  19. gilby959798

    C10 Fall Revival 2025, Denton, NC

    Is anyone going to the C10 revival in Denton, NC October 17 and 18th? I plan to go out on the 17th but since my truck is in pieces, its only to hang out and look around.
  20. gilby959798

    Gas Tank supports, what do these fit?

    Correct, do the the bend in the frame the front bracket is shorter than the rears.
  21. gilby959798

    Gas Tank supports, what do these fit?

    For instance, this is a zoomed in pic of the front driver side bracket, the passenger side would be different to match the bend in the frame, similar to your first pic.
  22. gilby959798

    Gas Tank supports, what do these fit?

    I think that is the passenger side front bracket
  23. gilby959798

    What have you done to your square lately??

    I cleaned up the shop more (put the tools away and such) then cleaned up the steering gear box to prepare it for new seals. Going to try to get the transfer case in the wash tub so I can start getting that clean. We will be doing new shifter shafts to try to get the lights working in the dash as...
  24. gilby959798

    Scottsdale Spear Molding

    Quickly drew something up. Need to export it and try to print it but the rear end piece will be easy if I can get the spear right.
  25. gilby959798

    Scottsdale Spear Molding

    I might try to make them and 3d print them if I can figure out how to do the chrome. I wish I had a CNC machine, I would try to do them that way.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,192
Members
43,338
Latest member
hauto85
Top