Search results

  1. rich weyand

    Electrical Load Causing Weak Blower Motor?

    One more thing no one has mentioned is grounds. We tend to think in terms of supply, and ignore the grounds. On our trucks, there are four devices that need to be connected for grounds to work: the battery, the alternator/engine block, the frame and the cab. There is a small wire from the...
  2. rich weyand

    Edelbrock Carb and original Air cleaner

    I used this. Worked fine. https://www.jegs.com/webapp/wcs/stores/servlet/SearchResultsPageCmd?q=555-50071
  3. rich weyand

    Sealing Bed Wood

    This is what my (excellent) contractor uses on any wood outside. https://www.minwax.com/en/products/protective-finishes/water-based-helmsman-indoor-outdoor-spar-urethane
  4. rich weyand

    454 Timing

    Everything you ever wanted to know about ignition timing.
  5. rich weyand

    454 Timing

    Everything you ever wanted to know about ignition timing.
  6. rich weyand

    305 serious sludge

    I'll second Mobil 1. The other thing that leads to engine gunk is no PCV valve or a broken PCV valve. Make sure you have a functional PCV valve on the engine. Just get a new one to be sure; they're cheap. If the PCV valve's been removed, put it back. Blow-by of the exhaust gases past the rings...
  7. rich weyand

    K5 3” lift question

    Haven't seen anybody mention this possibility. I went with a Tuff Country 2" on the front and 3" on the rear of my K10. They'll set up that kit for you if that's what you want. It made the fender cutouts on the front and rear match in height, and it was a good look. Ride was MUCH better. No...
  8. rich weyand

    dose anyone have any good pictures of a 3inch body lift

    I did a 3" suspension lift in the rear and 2" suspension lift in the front. I thought it looked pretty good. A body lift, though? Much more work, and looks funky.
  9. rich weyand

    Dual tank install

    Make sure you know what year the bed is. The tank setup changed in 1979. It changes the filler necks and hoses, and the wrong ones won't work. LMC has all the parts you need except the Pollak valve, but you can find those. They're about a hundred bucks.
  10. rich weyand

    Can't get rid of play in the steering

    Minne was loose until I replaced the ball joints. Moog.
  11. rich weyand

    K20 upgrades. EDELBROCK AVS II. Why so negative ?

    I ran with the Edelbrock. I played with the springs to get the mixture change to kick in at the right spot. I also put an AFR meter on it and played with the jets and rods to tune the AFR to precise values. Together with a thermac air cleaner and cold-air induction, I was giving it 95-degree air...
  12. rich weyand

    fixing hood hinges

    You can't get grease in all the little tight spots in those hinges. Before you buy new, hit them with Kroil and see if that fixes the problem. Kroil
  13. rich weyand

    350 small block

    Nobody mentioned the fact that the choke on an Edelbrock (and many other carbs) will stay in the 'warm engine' position (choke plate open) when the engine is turned off. I always needed one accelerator push to the floor for a first-key-on start. That takes the choke off the 'warm engine'...
  14. rich weyand

    Can the heater core be turned off?

    I just put a ball-valve in one of the lines and shut it off in the summer. No issues over several years with a first-gen 350 crate engine.
  15. rich weyand

    Cooling Questions and Concerns

    Couple things. - 350s usually run cold. Cooling them isn't an issue. The big blocks typically run hot, and it can be an issue. I closed off the bleed hole in the thermostat, which lets some coolant circulate all the time, and drilled a smaller one. Winter engine temps went up and mileage...
  16. rich weyand

    Heater not very hot

    I put a cover over the center of the grille in the winter. I just used a Chevy Truck fender pad.
  17. rich weyand

    Is there such a thing as Cams for Dummies

    Couple things to bear in mind. You drive torque, you race horsepower. Racing engines always have 'a lot of cam', which is to say, they're cammed for high RPMs, because they don't race them at low RPM. They put the throttle down and keep it there. Driving, you use torque. You're usually at low...
  18. rich weyand

    Decorative front license plate poll

    The official plate. Front plate. 'Working Girl' because: 1) everything works. 2) daily driver. 3) if I buy her presents, she lets me ride her.
  19. rich weyand

    EFE, traditional Heat riser & thermac informational

    Yeah, everybody does the two chrome pie plates thing with air cleaners and then wonders why the thing runs like garbage in the winter. That's a southern California thing, people. Most of the country should be running a thermac. BTW, they do the same thing on planes, where it's called carb heat...
  20. rich weyand

    Sbc dumping oil

    Make sure you wipe the rubber seal on the oil filter with oil before you put it on. This will keep you from buggering up the seal when tightening. After the first heat cycle of the engine, get under there and retighten the oil filter. A heat cycle sometimes loosens them up a bit.
  21. rich weyand

    Disappearing coolant

    Also could be a warped head, not just a cracked head or bad gasket. On a 195 straight six, I put the head gasket on with #2 Permatex on both sides and torqued it down. What?! you say. Yes, but I got another 150K miles out of it, and it had 100K miles on it when I rebuilt it. A warped head...
  22. rich weyand

    NP203 fluid

    The first number on oil is the viscosity when cold. As the transfer case never gets hot in an engine sense, the oil will never ride the temperature curve to the second number viscosity. The first number is the effective viscosity for the transfer case application. I would prefer running...
  23. rich weyand

    How do YOU set timing?

    I run 17 BTDC at idle with the vacuum disconnected. That should be something like 52 BTDC at cruise, with mechanical all in and vacuum all in. I wrote up a detailed description of timing, including all the whys and wherefores, a while back...
  24. rich weyand

    truck runs hot

    Usually the classic big blocks run hot and the small blocks run cold. I will support the statements here: 1) check the actual water temp by reading the thermostat housing with an infrared thermometer; 2) make sure your vacuum advance is hooked to manifold vacuum. Ported vacuum is pollution...
  25. rich weyand

    Help with wiring!

    Is the ground from the rear of the passenger-side valve cover to the firewall in place? If that is missing, the cab will be floating, and all kinds of crazy stuff will happen.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,339
Latest member
hauto85
Top