Search results
-
Tank strap issue
Did the threaded strap go into the top or bottom hole on the mount?- Doppleganger
- Post #5
- Forum: Tech Discussion
-
Tank strap issue
So I'm preparing to install my sending units and realize something: The tanks are mounted too far back (5" maybe?). Basically one set of mounting holes off. The rear just needs moved up one set of holes - the front can only mount one place but the tank has to go forward a few inches. No biggie...- Doppleganger
- Thread
- Replies: 61
- Forum: Tech Discussion
-
EFI Sender and EP381 Pump Install
I just want to confirm I have to grind out the pump seat on the sender to make the GM pump fit. Have never heard anyone mention doing this before. No biggie.- Doppleganger
- Post #3
- Forum: TBI & EFI Conversions
-
EFI Sender and EP381 Pump Install
Figured it out.- Doppleganger
- Thread
- Replies: 2
- Forum: TBI & EFI Conversions
-
1976-87 dual tank harness available!
This guy was exiled to the island of Elba years ago. Wait - that was Napoleon. This guy was just banned. Surprised his avatar doesn't say anything.- Doppleganger
- Post #8
- Forum: Electrical & Audio
-
Taking a Vote or opinions.
My favorite square grill....wish mine was a Jimmy just so I could use it. Maybe try it in a darker silver / charcoal?- Doppleganger
- Post #19
- Forum: Exterior
-
Greetings from Texas
- Doppleganger
- Post #10
- Forum: Introduction
-
Greetings from South Dakota
- Doppleganger
- Post #5
- Forum: Introduction
-
Electrical and Harness Repair Parts
I think this guy was banned years ago. USA1 is faster. lol- Doppleganger
- Post #64
- Forum: Electrical & Audio
-
Low Pressure Return Line PSI
Its actually a size smaller - which I thought strange.- Doppleganger
- Post #3
- Forum: TBI & EFI Conversions
-
Low Pressure Return Line PSI
The supply line on my EFI is 56-58psi - what is the return PSI? A 30R7 line be ok? My supply lines are 30R9 - I have enough 30R7 to do the returns - 30R9 seems way overkill but I know some of these systems will have about the same PSI returning as the supply. Just curious.- Doppleganger
- Thread
- Replies: 2
- Forum: TBI & EFI Conversions
-
Pollack Valve Wire
There was 2 different questions - 1. what does the pink wire that goes to the gauge carry....volt, ohm, etc, and 2. what is that single wire with the button end on the sending unit for? Since I am going to FI, I am swapping in new sending units (and Pollack valve) from an 87. They do not have...- Doppleganger
- Post #7
- Forum: Tech Discussion
-
-
Pollack Valve Wire
There is a single wire from the Pollack tank switch valve (pink?) that goes to the fuel gauge. Is this signal a 12v, mV, ohm? Also, does anyone know what this wire goes to (GND? Fuel gauge?). Thanks.- Doppleganger
- Thread
- Replies: 6
- Forum: Tech Discussion
-
Tank Selector Switch Dash Side Connector
Now to find one...... They dont make a replacement pigtail. THX- Doppleganger
- Post #3
- Forum: Wanted
-
Tank Selector Switch Dash Side Connector
Found one. Thx.- Doppleganger
- Thread
- Replies: 3
- Forum: Wanted
-
-
-
New Guy (kinda) from South Dakota
- Doppleganger
- Post #3
- Forum: Introduction
-
-
-
-
Show your daily driver
There's a guy in PA that has a wagon with a twin turbo'd Vette motor. Once posted a video of his friend pacing him on a bike - his speedo read 168mph and the wagon was pulling away. I guess a good wreck at almost 200mph will show just how safe they are.- Doppleganger
- Post #958
- Forum: Other Vehicles
-
Hide engine wiring
This is the stuff I always used on restos - not cheap but very heat resistant, easy to clean and very OE looking. Used alot on motorcycles (for heat) too. Not split either so more effort to install. https://www.amazon.com/dp/B0B6FJVH5K/ Never cared for the plastic split loom unless its...- Doppleganger
- Post #6
- Forum: Electrical & Audio
