Search results

  1. C10MixMaster

    High Beam?

    to the best of my recollection you should be able to push the rod back into place just operate the lever so you can feel it engage and then reinstall the switch.
  2. C10MixMaster

    Gear ratio for 35 inch tires.

    you can add dip switches to the drac module and change the speedo reading with the flips of a couple switches (I was modifying and selling these on ebay a while back)
  3. C10MixMaster

    Thinks shes gunna blow!

    check the fan and shroud. also a long screw driver or extention pressed against you ear and various areas of the engine can help locate the noise.
  4. C10MixMaster

    Electric Choke Issue

    you have a bad connection or switch. Use you voltmeter checking voltage and work your way back to the power source. could be bad crimp,bad wire, or bad switch
  5. C10MixMaster

    Worn out leaf springs

    if you are happy with the height you can disassemble and mix and match the leafs till they sit equal. I did that on my current truck . or get yourself a fat girlfriend :rotflmao:
  6. C10MixMaster

    10 bolt leaks but not where you would think

    sounds like you have a loose axle tube. sometimes the plug welds let loose. There is no seal , they are press fit and then welded. your best bet will probably be to replace the whole assembly.
  7. C10MixMaster

    In-op speedo advice

    You can spin the cable with your fingers fast enough to make the speedometer read, so i doubt it is your drill. Probably not the speedometer itself . check to see if the upper cable is in the back of the speedometer it pops in and i just held in place with a spring clip. you can reach up and...
  8. C10MixMaster

    Power Windows issue

    the fact you have one window that works basically verifies the ground and power are good. probably dirty switches. squirt some wd40 in them and work them back and forth several times. They alternate the power and ground so both switches have to work for each window.
  9. C10MixMaster

    Has anyone done the $50 Rustoleum Paint Job on their Square???

    i did one on a 73 cj5. thinned it and sprayed it. biggest complaint was it does not resist uv well. It got chalky with age.
  10. C10MixMaster

    Bracket

    im thinking a bracket for the hi speed tail light gears. but i have been wrong before. :rotflmao:
  11. C10MixMaster

    Home built wood engine stand?

    that's a little hi closer to 5-600#
  12. C10MixMaster

    Power window switch issue

    take a can of wd40 hose down the switch and get as much in it as you can then work the switch back and forth several times. you would be amazed how often this brings back a dead switch.. can do this with the switch still in the door.
  13. C10MixMaster

    4L80 or OK with 4L60

    i would use the tranny from the same donor the 6.0 came from . that way the comp and harness already match.
  14. C10MixMaster

    Issues after reassembling steering column

    things that will cause a steering wheel to feel loose. the 4 bolts at #61 in the pic are known to loosen you would have to loosen the whole column again the pivot pins at#39 can come loose or you missed something on the upper shaft there should have been a lower bearing, lower race,upper...
  15. C10MixMaster

    Missing vin on k10 can they be swapped over from a parts truck with most of the parts?

    there's also vin numbers stamped on the frame in various hidden places. if they dont match the vin plate you could have an issue some day.
  16. C10MixMaster

    Coolant overflow hose

    uses a spring clamp to hold it in place. The hose should go nearly to the bottom of the bottle but not touching the bottom.
  17. C10MixMaster

    Which PAG Oil to Use

    what you have in the picture does not look like an A6 heres what an A6 looks like I did use pag 150 when i did my r134 retrofit.
  18. C10MixMaster

    Which PAG Oil to Use

    the compressor is the only thing that needs oil in the system so if it says pag 46 that's what i would use. If in doubt call the company selling the kit.
  19. C10MixMaster

    Number of Original Circuits

    most aftermarket radios have a always hot B+ lead, for the memory, that would connect to F on the above picture. most aftermarket radios also have a switched lead or accessory lead, to turn it on and off, that would connect to C on the above picture the factory radio connects to accessory or...
  20. C10MixMaster

    Any value in dummy light cluster?

    Does it have any value? I would say as old as our trucks are most any part has some value to the right person. Is it worth switching to gauges? I prefer gauge, just realize it's more than just plug and play, the wiring and sending units are different.
  21. C10MixMaster

    Browne/White wire issues

    Looks like you have a bad resistor wire for the alternator. could have fried from a bad alternator,short in the engine compartment or after nearly 40 years of cycling the aluminum wire just gave up. Mine fried in my first truck and i had smoke rolling out of the dash:flame:. I have not seen a...
  22. C10MixMaster

    Custom alternator voltage

    Your truck will run on 15.5. But you will shorten the life of things like your ignition control module, light bulbs and battery. pushing 15.5 volts into your battery in the middle of the summer will be real hard on it. I think going to a higher Amperage alternator is your best bet.
  23. C10MixMaster

    Steering wheel installation

    dorman Part # 49319 any auto parts store
  24. C10MixMaster

    Steering wheel installation

    remove the spring loaded contact replace with the spring loaded wire. total time to instal 2 seconds.
  25. C10MixMaster

    Connector under dash

    since no one has chimed in . I'm going to guess left dash speaker. I can swear i've seen that connector but not on my earlier truck.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,340
Latest member
hauto85
Top