Search results
-
-
Putting a gas 350 in a 6.2 diesel frame, quick input please.
I put a 350 in my 85 C10 short bed that had the 6.2 diesel. I used the stock diesel clam shells and motor mounts. I took all the diesel related stuff off. I used the two glow plug wires as 12V to the HEI distributor and anything else that needed switched 12v. I removed the hydroboost system and...- custodian
- Post #13
- Forum: Diesel 6.2, Conversions Cummins, etc.
-
Lost Fuel Pressure
I was hoping too. Going the grease on the push rod route and maybe a a small screw driver to hold it up.- custodian
- Post #17
- Forum: Carb Fuel Systems
-
Lost Fuel Pressure
I don't think there is a bolt on the front of a BB 454 like the the SB 350 to hold the fuel pump rod in the up position.- custodian
- Post #14
- Forum: Carb Fuel Systems
-
-
-
Lost Fuel Pressure
I did some testing this morning. I used a fuel pump that I use to crank LS motors and hooked it up to the fuel line coming from the transfer switch. I was able to pull gas from both sides. I then put a fuel line into a small gas tank to the fuel pump and tried to start the truck, no luck. SO...- custodian
- Post #6
- Forum: Carb Fuel Systems
-
Lost Fuel Pressure
Yes, mechanical pump on the motor, 454, and no fuel when I removed the inlet line to the pump.- custodian
- Post #3
- Forum: Carb Fuel Systems
-
Lost Fuel Pressure
I was driving my 86 Dually home after putting some gas in the drivers side tank and it just cut off. Had my wife come and pull it home. I poured some gas in the carb and it run. I removed the fuel inlet at the carb, no pressure, and put an empty clear bottle on the end of the line and turned the...- custodian
- Thread
- Replies: 23
- Forum: Carb Fuel Systems
-
Quadrajet Idle Mixing Screws
I took the carb loose and sprayed them with PB Blaster. They turn now.- custodian
- Post #4
- Forum: Carb Fuel Systems
-
Quadrajet Idle Mixing Screws
My idle mixing screws will not turn on my 86 C30 with a 454.- custodian
- Thread
- Replies: 3
- Forum: Carb Fuel Systems
-
3 Wire Temp Sender
I'm doing an LS Swap in the 85 C10 with gauges. How can I wire the 3 wire temp sender from a 97-98 Corvette/Trans Am be used/replace the one wire temp sender and still use the gauge in the 85 C10?- custodian
- Thread
- Replies: 3
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Cruise Control Wiring
I have an 85 C10 that I'm doing an LS swap and want to use the cruise control wiring to send the VSS signal to the computer. There are five wires. Just not sure what each wire is for. I've looked through the wire harness section and couldn't find the plug that I have. I'll post pictures of the...- custodian
- Thread
- Replies: 1
- Forum: Tech Discussion
-
1973 Impala/Caprice gas pedal
Yes, I'm doing an LS swap in the 85 C10 and going to hook the detent cable to the gas pedal. -
1973 Impala/Caprice gas pedal
I'm looking for a 73 Impala/Caprice gas pedal. I've already looked on ebay. -
Detent Cable
Okay, I have pan off and will look. I've been schooled!- custodian
- Post #3
- Forum: Automatic Transmission
-
Detent Cable
Someone is going to have to school me on this. I have a 350 Turbo trans I'm using in an LS Swap. I want to put a new detent cable in it but cannot find the same hookup in the tans, I have the cable that slips into the hole on the bracket, I'll post a pic. All I'm finding is the cables with a...- custodian
- Thread
- Replies: 3
- Forum: Automatic Transmission
-
What year is my 350 Turbo Trans
I bought a 350 turbo trans for my LS Swap. I'm looking for a new detent cable and can't find one that mounts the same inside the trans. The only numbers it has on it is 12K528025. I did an Internet search on that number but could not find anything. I'll attach a picture of how the detent cable...- custodian
- Thread
- Replies: 1
- Forum: Automatic Transmission
-
Bulkhead wiring ..HELP ..1976 K10
If I remember right, I didn't use them. I'll go out and look.- custodian
- Post #7
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
-
No Longer For Sale.
I'm looking at selling my 86 C30 Dually. $9,500. I live in Catawba, NC. Here is some info. When I bought the truck it had a flat bed on it and I changed it to the regular bed. This bed doesn't have any rust on it. The cab has some rust near the doors on the floor board. I have more pictures if... -
Rebuilding the Hydroboost
I got the unit apart today and found that the seals in the kit do not match the ones I took out except for the "8" looking seal. In the second picture, the original seal is the one on the bottom. In the third picture, the original seal is the bottom right. I believe this unit has been worked on... -
Rebuilding the Hydroboost
Any tips on rebuilding the Hydroboost? -
4spd to Turbo 400
I'm not using the truck as a work truck, just something different to drive around with the granddaughters is their C10's that I gave them.- custodian
- Post #7
- Forum: Manual Transmission & Clutch
-
Which Impact Tool
I ended up buying the Dewalt DCF900 with the battery, charger and carrying bag. 1030 fasting torque with 1400 loosening torque.
