Search results

  1. Mike_82_Shortbox

    No start and I am stumped

    Just my two cents after reading through this thread. If you're getting good fuel and good spark, then even if the distributor and camshaft are 180° out, you're going to get some kind of crazy backfiring, coughing through the carburetor, maybe even a fire. What you need to do is disconnect all...
  2. Mike_82_Shortbox

    86 K10 starter won't stop cranking

    Did you try the simplest thing and just shim the starter? It may be that when the starter gear engages the flywheel ring gear, the pressure against it is enough to overcome the force of the solenoid retracting spring, and hold it in place when power is removed from the solenoid, thus...
  3. Mike_82_Shortbox

    Front brake pads ceramic or semi matallic

    This is what I know about ceramic brake pads. Ceramic pads are comparatively ineffective when they're cold. In fact if you are used to driving organic or semi metallic, the first time you leave in the morning with ceramic pads, they will downright frighten you the first time you try to stop...
  4. Mike_82_Shortbox

    Converting from dual saddle tanks to a single fuel tank

    Don't. Those saddle tanks are up out of the way, they're protected, and they hold 32 gallons of fuel. There's no we can get that in a single fuel-cell sitting between the frame rails. Not to mention the fact that there's no place to put a 32 gallon fuel tank between the frame rails and keep it...
  5. Mike_82_Shortbox

    700r4 Overdrive

    There are some different ideas of what overdrive means on a 700R4. The 700R4 is essentially just a four-speed automatic transmission that is good for about 350 foot-pounds of torque. It is 100% mechanically governed; no solenoids, no vacuum, no TCU. It's the original plug-and-play transmission...
  6. Mike_82_Shortbox

    700r4 Overdrive

  7. Mike_82_Shortbox

    This blows...

    The best thing to do would be to simply underdrive it by quite a bit, using a bigger pulley on the blower and a smaller pulley on the crank, and you can run the blower all day with no boost and the engine won't even know it's there, but it will still look awesome... And you know Derek from Vice...
  8. Mike_82_Shortbox

    305 serious sludge

    That's exactly what happened to me on a V6 Ranger many years ago. While I was working at a commercial shop. Everybody told me not to mess with it (I was sort of new), but I was convinced that all that junk needed to be scraped out, and it was about 10 times as bad as this car. So after I did...
  9. Mike_82_Shortbox

    Custom Fuel Tank Location - Filler & Vent Hoses.

    The name of it there in the original message is a link the page, https://classicparts.com/chevy-gmc/chevy-gmc-truck-parts/1973-1987-truck-parts/fuel-system/1973-87-hidden-tail-light-fuel-filler-kit-sku-23-043-driver All three things are linked in the original message, the hidden taillight set...
  10. Mike_82_Shortbox

    Custom Fuel Tank Location - Filler & Vent Hoses.

    Greetings Guys and Gals! I just got an email from the forum saying it's been a while since I posted, which prompted me to post about my latest problem. I'm installing a square, center-mount fuel tank from Tanks, Inc. i.e. 1973-81 Chevy Blazer Fuel Injection Gas Tank [<—link]. The tank has a...
  11. Mike_82_Shortbox

    Nylon cam gear years

    I'm probably late to the game here, but the Chevy 396/454 is not an interference engine. The nylon sprocket can blow itself to pieces at 80 miles an hour on the freeway, and you can just replace the timing gear and chain set and be on your way.
  12. Mike_82_Shortbox

    I’m pretty pissed!!

    I feel your pain. But some of that pain is your own doing. I'm wondering why you didn't just return the bushings when you couldn't find suitable inner sleeves, and why and how you managed to install them if you didn't have sleeves that were the right size. Mere friend just finished a year's...
  13. Mike_82_Shortbox

    Adding 4WD, where does the shifter go?

    OK, we're going to give it the college try! Thanks for your help guys!
  14. Mike_82_Shortbox

    Adding 4WD, where does the shifter go?

    Hey, Bill, Yes, that's what I've got. A shifter from the correct truck, with the single linkage rod on the bellcrank on the 208. The hard-to-type kkgp81 sent me in the direction of an aftermarket hump, so I found one and got the pictures, so I have an idea of the placement, but I wanted to find...
  15. Mike_82_Shortbox

    1984 k10 700r4 won't shift out of 2nd please help!

    Well, truthfully, this transmission is probably never going to see more than 300 hp, so I should be okay with it for a while, but if I do blow this one, my next step is 4L60E. I don't need an 80. We'll see this summer after I put 9:1 pistons and another new cam in my 400, this time a Comp Cams...
  16. Mike_82_Shortbox

    700R4 Hard/Delayed 1-2 shift

    Before you try all that just try loosening up the throttle valve cable about 1/8 of an inch and see what happens.
  17. Mike_82_Shortbox

    1984 k10 700r4 won't shift out of 2nd please help!

    I just had a nightmare of a time fixing my 700R4. Two years. Two shops. It did the same thing, stopped upshifting, so I took it in, cost $1800 to rebuild it. Then I forgot to torque two of the bolts on one side of the transmission, it came off the block and destroyed the front pump. Another...
  18. Mike_82_Shortbox

    Does it matter where this spring connects?

    Well, Ricko is right, mechanically, and from an engineering standpoint, what he describes is exactly how the system should work. Functionally, if you have the spring a little bit off-center, pulling down on the shaft at the same time it pulls the throttle cable forward, then you are exerting...
  19. Mike_82_Shortbox

    Adding 4WD, where does the shifter go?

    Oh. Sorry. That information might be helpful. It's a 1985 GMC K2500 frame with a 208C transfer case, and a 1985 Chevy C1500 cab.
  20. Mike_82_Shortbox

    Adding 4WD, where does the shifter go?

    Hi guys, I put a two-wheel drive cab on a four-wheel-drive chassis, because the thing caught fire. Now it occurs to me I don't know the exact measurements where to cut a hole in the floor for the four-wheel-drive shift linkage. Can any of you guys help me out? Got dimensions in hand? Take a...
  21. Mike_82_Shortbox

    HELP motor mount issue

    Hi guys, I'm new to the forum, I came here to get some help on just this topic. I have an '85 four-wheel-drive frame I'm putting a '99 5.7 L Vortec into, and I confused myself at first because the motor mounts wouldn't fit, so I thought maybe it was a 454 mounting problem, which is where the cab...

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,173
Members
43,337
Latest member
kfrdavid
Top