Search results

  1. bluex

    Car Hauler tips/tricks/ideas

    All right brain trust, is this beefy enough? This took a bit of planning but it turned out how I wanted, unless it's not solid enough. The angle underneath is 1/4", all bolts are 1/2" grade 8 with prevailing torque nuts, also grade 8. The crossmember it's bolted to is 3/16" i believe. With the...
  2. bluex

    Show your daily driver

    That was the idea with this buick. It was just neglected a bit by POs. I about have it sorted now I think. It still occasionally does some weird stuff but I mainly just use it to get to work so who cares lol. The cooling system was full of sludge. This was last piece, honestly it was probably...
  3. bluex

    Show your daily driver

    This is why new cars suck. Take apart the whole interior for something that should be a 45 min maintenance job :doh2: An on top of that, not only were the covers bolted on, they had heat stakes that had to be ground off too. Why both????
  4. bluex

    C30 front end bagged and now tie rods are too long

    Cut about 1/2" to 3/4" off each tie rods so they will screw together more. Not an uncommon issue on bagged or really low stuff.
  5. bluex

    Old77's 1989 S10 tinkering project

    Check the wiring diagrams for it. If it's setup like a 88-95 GMT400 the speedo goes to the drac an the drac feeds the cluster, cruise an ecm. As long as the drac has power/ground the speedometer should work with everything else removed. Temp an oil pressure should go direct to the cluster as...
  6. bluex

    late GMT400 interior lights wont shut off like a door is open.

    Check the sill plates. The wiring runs through there an if a screw caught the ground wire they would stay on. They also like to break at the B pillars right at the transition from the sill plate to the B pillar trim. Could be worn through but not broken yet an grounded to the floor. Also since...
  7. bluex

    What have you done to your square lately??

    Love it man! I have a standard tpi with a voretec lower I'm going to put on mine soon an run with a terminator. When I do my 383 I have a super ram with the tpis lower.
  8. bluex

    Control Arm question

    I don't know about those specific arms but those are generally not a super tight fit. They should come out without needing a press. Pretty sure your noise is coming from between the bushing an the chassis mount though. Try spraying something there to see if it goes away before disassembling
  9. bluex

    Control Arm question

    You'll probably have to take them back off an remove the bushings to grease them. It's also possible it's only squeaking on the side between the bushings an the chassis mount. Either way you'll have to take them lose to do it right.
  10. bluex

    Control Arm question

    What arms did you buy, you left off the link. It depends on what the bushings are made of on of they are greasable or not.
  11. bluex

    73-80 Squarebody XJ Steering Shaft Upgrade

    It is at the top of this section, first sticky thread. Title is retro mod jeep intermediate shaft
  12. bluex

    73-80 Squarebody XJ Steering Shaft Upgrade

    There is a much larger thread on this pertaining to 81 an up trucks. It is a bolt in swap for those using the whole jeep shaft. An XJ is the box style Cherokee from the late 80s to 90s. Specific years are in the other thread, but you can't use a Grand Cherokee as those used a different column...
  13. bluex

    What have you done to your square lately??

    Looks great out in the day light!
  14. bluex

    What have you done to your square lately??

    When it strips out, your screwed. Hard to clean corrosion off, hard to add circuits too an keep it clean looking, they never seem to stay tight. I'm sure there's more but that's what I got right now... My main hatred for them is from GMT400 trucks and the dual cable positive they had. Those are...
  15. bluex

    What have you done to your square lately??

    Don't go side terminal, you'll regret it. If you have it in the tray an properly secured, it will be fine. They sell rubber covers for top post terminals as well. Many racing sanctioning bodies require them.
  16. bluex

    Repositioning Tilt Steering Column closer to dash

    I moved mine in 2" by putting the bracket forward on only 2 bolts. No issues from it but I don't have a neutral safety to worry about either. Not sure that would work well on an automatic
  17. bluex

    Bowler Clutch pedal?

    Any questions just ask, the NV4500 is not a sporty trans at all though. Tough yes but not quick shifting sport car stuff at all. Just fyi...
  18. bluex

    Car Hauler tips/tricks/ideas

    Ya these have a cover sleeve but it seems it's almost the same material as the strap, like it's just to help keep the strap from getting abrasion itself. I found some fleece covers that I might get. I'm ready for different wheels on it so I'm not to worried about those, they are far from perfect...
  19. bluex

    Car Hauler tips/tricks/ideas

    I don't mind at all, that's what this thread is for. I want to learn what's good/bad, easier ways, better equipment etc. I probably know enough to be safe but it could also be just enough to be dangerous too. I thought about crossing the front ones but I didn't like how it was pulling on the...
  20. bluex

    GMT 400 W/T

    To go from a 4.3 to a V8 he'll have to remove the offset brackets from the crossmember an install the mount directly on it. Not terribly hard but nit much fun either. A swiveling 13 socket is very helpful.
  21. bluex

    Car Hauler tips/tricks/ideas

    These through wheel straps popped up on Amazon this week for $36 so I thought I'd give them a try. It was/is just the strap an no ratchet. I actually like them, just need to pickup a pair of ratchet handles that have the hook straight on them for the rear. An maybe some softer covers if I ever...
  22. bluex

    CPP Upper Control Arms and Shims

    I don't disagree with anything huck said. Check your bushings too, honestly if they need replaced I'd buy the tube uppers. The bushings are cheap but pretty labor intensive to replace an you run the risk of bending the arm when pressing them in if you aren't careful. I see another post below...
  23. bluex

    Need Help with Rear Brakes.

    :doh2: an that's what I get for not reading everything before commenting :sad72:
  24. bluex

    Need Help with Rear Brakes.

    The proportion valve is tripped an blocking the rears off. Either recenter it manually or go ahead an bleed a front. That should make it move to block off the front an allow you to bleed the rear. Ive had to go back an forth a few times to get enough pressure in the rear circuit to keep it...
  25. bluex

    Time for new shocks. Look at these!

    I treat kybs like hot sauce, I put that sh!t on everything!

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,187
Members
43,339
Latest member
wonone
Top