Search results

  1. D

    Dakota Digital RTX Install Critique

    Finally started mine today after having it sitting in a box for almost 2 years. SquareRoot - what all did you NOT use on your setup because its already fed by the PF4 system? Coolant temp? Tach?
  2. D

    Wiring Harness? Choosing one?

    I went with the Painless kit myself when i did mine. The difference being the documentation and instructions in the book
  3. D

    K10 fuel line for Holley sniper truck has dual tanks but I’m buying the hokey tank with the efi fuel pump it I’m needing a line kit for just one tank

    I ended up buying pre-made length SS braided with AN fittings for the supply side. I ran the return in rubber fuel-injection rated hose
  4. D

    Dakota Digital RTX Install Critique

    Just future readers - i did ask, and they do not have anything other than the single BIM bracket
  5. D

    What aftermarket engine harness?

    I know there is a sort of block from the factory in that same location. Sorry, I'm not a ton of help. But there are some absolute geniuses here who know these trucks inside and out and they'll be able to help you
  6. D

    What aftermarket engine harness?

    Ok my painless kit, it came with a new fuse block. Power wire went from fuse block and then teed off there to catch there starter. I am not familiar much with the electrical and how it works - i just followed the instructions I will say that when I was researching which harness to buy, the...
  7. D

    What aftermarket engine harness?

    I used the Painless kit last year. Worked out well
  8. D

    Have you checked your ground?

    Good info - thank you
  9. D

    Have you checked your ground?

    I finished a re-wire of my 77 a few months back. One of the things I did was to completely create new grounding points with threaded studs and nuts/washers 1 - underneath bed between fuel tanks 1 - at rear fram 1 - at firewall, next to fuse block 1 - at driver side fender 1 - at driver side...
  10. D

    New wheels and tires for the 77

    Drivers side is before, passenger is after
  11. D

    Steering Column needs to be rebuild

    I rebuilt my 77 tilt column myself. It wasn't fun but I got it done. All new parts when available, including bearings and the little pivot ball thing. The worst part was that I had collapsed the little plastic shaft holders without realizing it, and it took forever to realize why the shaft...
  12. D

    Replacement doors?

    Good info. Will probably just hit them with a can of black primer or something
  13. D

    Replacement doors?

    Not planning on paint. This is more meant to be an offloading/camping truck, so not planning on paint anytime soon
  14. D

    Replacement doors?

    As far as the dust getting in, i meant that as in the cab is open to the elements because one window is broken and the other is stuck in the down position
  15. D

    Replacement doors?

    I'm almost ready to start on the interior of my 77 K10. Last thing I need to do before that is to get both of the doors rehabbed, as the passenger side window is broken and the drivers side glass doesn't stay up unless I shim it into place. I don't want to have the interior rebuilt and nice...
  16. D

    Wiring Harness journal

    I hear you. Mybwiring was so chopped and spliced up that I would never have been able to relax or trust it not to leave me stranded someplace
  17. D

    Wiring Harness journal

    There's some really good information on this board, as well as many many people who know much more than me. What I will tell younthough is that if I could figure it out, anybody can. I am about the dumbest person alive when it comes to electrical but I managed
  18. D

    Wiring Harness journal

    I would say if you're considering this to go for the two efi tanks and pumps, and have the Sniper system control the pumps, assuming it works the same as the ProFlo system. Also, if I had to do this again, I'd probably ditch the dual tanks and pumps and go with the larger Blazer tank...
  19. D

    Wiring Harness journal

    Correct- dual EFI tanks with dual internal pumps. I will say, my first version of this when I switched to EFI was running an external pump only. On the maiden test run, it just about left me stranded. The external pump was getting way too hot. I had to pull over every five minutes or so and...
  20. D

    HOW GEAR OIL?

    The B&M cover is designed to hold way more fluid than stock. It butt's out further and the fill port is much higher up
  21. D

    HOW GEAR OIL?

    Ok. You just exist to argue with people, don't you? That's pretty much I ever see you doing on here, is replying to threads to argue about the dumbest stuff. Do you not have anything better to do?
  22. D

    HOW GEAR OIL?

    I JUST drained and filled mine two weeks ago, with the B&M cover. It took a gallon and a half
  23. D

    Dakota Digital RTX Install Critique

    That's cool about the bracket. I didn't know they existed. Howbmanynmodules fit on there? I have four - the DD module, the GPS module, the ProFlo 4 module and the gear indicator module. Would all of these fit on that bracket?
  24. D

    LED Tail Light conversion… Carolina Truck Shop

    Are ads allowed here now?
  25. D

    Tank replacement for EFI

    I've read that running that pressure through the original lines isn't a good idea. When I did my conversion, I ended up running a new stainless braided AN line up to the regulator and a rubber high pressure line for the return.

Latest posts

Forum statistics

Threads
48,666
Posts
1,074,186
Members
43,338
Latest member
jw23655
Top