Search results

  1. squaredeal91

    1978 Toyota SR5- One for Dad

    No cerakote is a hard coating like powder coating but I think its thinner. Commonly used for fire arms and tools maybe
  2. squaredeal91

    1978 Toyota SR5- One for Dad

    I hate that clear coat some car lots use. Turns yellow over time and flakes off all over.
  3. squaredeal91

    1978 Toyota SR5- One for Dad

    I zoomed in on part of there description lol
  4. squaredeal91

    1978 Toyota SR5- One for Dad

    If I had that many 10mm sockets id most definitely lose some! Lol
  5. squaredeal91

    3/4 ton GMT400 Burb & ORD SAS and 6BT Swap

    So far ive got the front differential out and all the IFS BS out. Cutoff the upper and lower control arm brackets. Cleaning the frame up a bit with the grinder and planning my frame brace, these frames are made to carry the weight differently and they have a weak spot. Several companies make...
  6. squaredeal91

    Stalling under take off

    Glad you got it resolved
  7. squaredeal91

    Stalling under take off

    Like ricko asked. How long after you ran out of gas? Ive run out of gas a few time's in different rigs. If it were a clogged fuel filter it would likely have more trouble running on startup and get a little better after a few minutes. It could be a fuel pump failing too. Would be nice to be able...
  8. squaredeal91

    Stalling under take off

    Thought you replaced the filter recently but I guess its been 5 years. Maybe remove it and check filter flow. I hate these intermittent problems that can be multiple things. Have you checked egr valve?
  9. squaredeal91

    Stalling under take off

    Ill see if I can find a write up on it.
  10. squaredeal91

    Stalling under take off

    Its inside the distributor and can only be replaced when the distributor is out. It plugs into the icm.
  11. squaredeal91

    Stalling under take off

    Could still be pickup coil. Also check the wires going to the coolant temperature sensor on intake manifold by thermostat housing (has 2 wires) wiggle the wires while running. Odds are its the pickup coil.
  12. squaredeal91

    Stalling under take off

    With those symptoms its probably something in the distributor or like ignition module or pickup coil or ignition coil.
  13. squaredeal91

    3/4 ton GMT400 Burb & ORD SAS and 6BT Swap

    I finished my k10 manual swap project and have other projects started but been chipping away at this major project a while, mostly by collecting and saving parts for this project for a long time. Now lately ive been getting started on it. Platform:1999 K2500 suburban vortec 454 Build plan: *...
  14. squaredeal91

    What Trans for a cummins swap c10?

    Back to original question. thinking about it being a 2wd street truck the ZF5 isn't a bad option as it does shift faster than others. You can actually speed shift it. I wouldn't even consider a G360 because of torque.
  15. squaredeal91

    What Trans for a cummins swap c10?

    I forgot about medium duty Fords lol. Good point. Electric vacuum pumps do work. I might have to get one for my Mazda when I convert my alternator to a delco because the vacuum pump is attached to the original alternator and im done with making it charge
  16. squaredeal91

    What Trans for a cummins swap c10?

    The cummins engine has its own vacuum pump built in. The port is by the power steering pump on drivers side. I have mine hooked up to my brake booster and works great.
  17. squaredeal91

    HEI Modules

    Surprise!! I ordered 2 and they just arrived. They definitely look like there as old as the boxes are. They look like a gm module in lots of ways but they don't say anything. They are heavy and im sure good quality being as old as they are. Either way not a bad deal. Its just interesting that...
  18. squaredeal91

    What Trans for a cummins swap c10?

    I have a cummins truck and I couldn't afford an nv4500 so I ended up with the ZF5 speed and it works very well With my setup. Also you need to think about all the extra pounds. Its going to kill your wheel bearings. The engine alone weighs close to 1200#s lol. Im pretty sure the front suspension...
  19. squaredeal91

    Tire machine recommendations

    Those are good for most but not as good for aluminum wheels for scratching reasons. If you can try to find an overhead style machine. They are much more versatile and can mount/dismount wheels with reverse drop and do larger wheels h tires. Heck I wish I had any kind of tire machine myself so...
  20. squaredeal91

    4WD indicator switch on NP208 1987 V10

    Id remove the trans mount and then lower it down to the cross member and see if that gives enough room.
  21. squaredeal91

    Rear seal leak

    Im kinda surprised it is happening. But I guess 24 years could be why lol. I had a 305 in a 1990 caprice start leaking immediately after an oil change once. Changed oil again to what I normally used and it stopped leaking.
  22. squaredeal91

    Rear seal leak

    How many miles on the engine? And What oil are you running?
  23. squaredeal91

    Headlights only work when I press the dimmer button

    Exactly this ^^^ hyper flash that B
  24. squaredeal91

    83 K10 intermediate shaft seal

    Yes,Thats the input shaft. Wish I still had those part numbers. They had them in stock at the parts house.
  25. squaredeal91

    83 K10 intermediate shaft seal

    I just did both my steering box shaft seals. I got 2 kits to do it all. 1 for input shaft seal. 1 for output shaft (pitman arm shaft) seal The pitman arm kit comes with 2 seals because they are stacked inside with 1 washer in between the 2 seals and 1 washer on top below the clip.

Latest posts

Forum statistics

Threads
48,665
Posts
1,074,137
Members
43,333
Latest member
duncan_schawalder
Top