Recent content by vintovka

  1. vintovka

    thoughts on low vacuum?

    Get a wix metal the cartidges in some of the plastic ones come loose without warning and can dump all the collected junk into your carb.
  2. vintovka

    Update on my Ignition Module failure!

    Many modules are bad out of the box. Had 2 bad in a row off ebay. Ony one that still works was this one: https://www.napaonline.com/en/p/ECHTP45?ir=3&r-src=BR:PDP:SP:Belowproductdescription&ppid=MPETP45SB echlin says US made and 3 year warranty
  3. vintovka

    My 86 454 Conversion to Propane / Gasoline dual-fuel

    Nice job. parts prices here make me choke can't imagine them in Niederlande plus shipping!!!!!!!!!!!
  4. vintovka

    Steering Column needs to be rebuild

    I found using real red locktite on the 4 retaining screws works. Chinese "rock-rite" not so much.
  5. vintovka

    Steering Column needs to be rebuild

    $1500+???? gulp!!!!
  6. vintovka

    Steering Column needs to be rebuild

    I rebuilt my own 84 tilt. I followed the instruction link above. It was not easy. Took several tries and found that mine was so worn i needed to add a second washer/spacer to the column to get correct tension. If i had to do it again i would have it rebuilt by some else or replace it with a...
  7. vintovka

    Cheap defective aftermarket parts….lol

    I may be suffering my own filter failing and dumping debris in my Edelbrock 1406 carb. Every so often i get a misfire/backfire under acceleration. It happens every so often and goes away just as fast. Not sure its crapola randomly clogging the jets. Thoughts???? Should add that's a...
  8. vintovka

    Cheap defective aftermarket parts….lol

    Sorry not you. It was a guy with like an $15,000 engine that had one of these at a show. He blew a gasket when i asked if he knew his cartridge was floating around inside the plastic case. Never seen someone so upset and while I don't hold him responsible he really let me (and everyone...
  9. vintovka

    Cheap defective aftermarket parts….lol

    Been a couple months and was paying attention at the shows around here. About half of those using this type of see thru filter have failed. Checked each and all correctly installed with filter cartridge (originally) attached to the metal outflow plate per "flow arrow" marking. Most users did...
  10. vintovka

    Cheap defective aftermarket parts….lol

    Posted this on another forum and many cases are being reported so heads up. Several commenters have added that water removing additives like heet (alcohol) may be either increasing filter failures or causing them directly by dissolving the adhesives that hold the filter to the metal end...
  11. vintovka

    Cheap defective aftermarket parts….lol

    No - took pic at odd angle so looks just backwards. It was properly installed so flow arrow points toward carb with filter originally attached to metal body. Junk is supposed to collect in empty area before passing thru filter to carb. Think ethanol makes the filter cartridge comes loose...
  12. vintovka

    Cheap defective aftermarket parts….lol

    My earlier post about failed Asian plastic filters seems to have caused a bit of concern. Last show i saw several very expensive restorations with these that had failed. Owners not happy. Not just plastic but steel parts like bolts, carbs, brake component and alternators are becoming a costly...
  13. vintovka

    Cheap defective aftermarket parts….lol

    Couple months ago we noticed our filter looked odd. On closer inspection the cartridge had detached from the metal inlet side allowing all the debris to pass and partially blocking the outlet. This common chinese made filter was supplied by Edelbrock with a new 1416 carb. I have since seen...
  14. vintovka

    86 HEI no spark

    Mine made a lousy connection. hole too big, screw too small and poor connection.
  15. vintovka

    86 HEI no spark

    This is what caused me to junk mine
See more

Latest posts

Forum statistics

Threads
45,558
Posts
986,223
Members
38,643
Latest member
Hard
Top