Recent content by tkbp4him
-
T
no end play th350
Ok, got the anwsers.....ready? They installed my bushings for me and they put one in wrong...is what they said was causing me not to get end play. The bushing in the direct clutch was not in far enough which was pinching the pump causing me not to get the end play at all they said. All I...- tkbp4him
- Post #25
- Forum: Automatic Transmission
-
T
no end play th350
Hey, thanks for the help with the photo's "hot rod pc"....I have tried what your showing here already with no end play result with thrush washer or with shim and bearing and with nothing under pump and I still have no end play. I have run out of patience with it and I'm taking it to this guy...- tkbp4him
- Post #23
- Forum: Automatic Transmission
-
T
no end play th350
I don't know....I was gona try getting thinner thrush washers for either the front planet or the carrier gear that goes on top of the planet gears , ( the four tang or three tang) but after today asking a trans shop about that they said they only come in .061 thick size and that I had something...- tkbp4him
- Post #21
- Forum: Automatic Transmission
-
T
no end play th350
Ok I'll try that see what happens. I'm not going to try one of the orignal plastic thrush washers due to fact that it is definitly melted and plastic. I replaced it with the same thickness metal thrush washer. I am going to see if I can get some varity of washers to try that are three or four...- tkbp4him
- Post #19
- Forum: Automatic Transmission
-
T
no end play th350
I found in the book page 139 it says under preliminary front end play ck....that "It is controlled by the thickness of the selective thrust washer or bearing and shims that install (between the oil pump and direct-clutch hub). Does this mean I cant replace a three or four tang thrush washer...- tkbp4him
- Post #17
- Forum: Automatic Transmission
-
T
no end play th350
Well, does anyone have any thoughts on the solution to this end play issue, ive been told different things, not sure which is most used method that will give me longevity? Do I switch out thrush washer .061 for .030 which Ive been told they sell, but then in same sentence been told its better...- tkbp4him
- Post #14
- Forum: Automatic Transmission
-
T
no end play th350
in reply to hotrodpc I have used all new metal washers, shims and bearings...the trans orignally had a plastic one that melted along with input shaft damage from bad bushings. My real questions is : can I buy thinner tanged thrush washers say .030 size that go on top of the planetary gear set...- tkbp4him
- Post #13
- Forum: Automatic Transmission
-
T
no end play th350
I am reading HP books "turbo hydra-matic 350 handbook by Ron Sessions page 199 see diag. if you have of coarse...- tkbp4him
- Post #9
- Forum: Automatic Transmission
-
T
no end play th350
I am talking about above the sun gear there is what my book calls a carrier, output, it has four small round gears on outside and a geared opening in the middle which slides onto the sun gear, gear then on top of this four small gear carrier there is a four tang metal round washer that I call a...- tkbp4him
- Post #8
- Forum: Automatic Transmission
-
T
no end play th350
no end play ok, no end play update....I found out that the shim and bearing under the pump is not the problem...no matter what I do with the shims and bearing under pump I will not get end play, due to the pump bottoming out inside the input shaft. I removed a thrush washer on top of the...- tkbp4him
- Post #6
- Forum: Automatic Transmission
-
T
no end play th350
ok, Ive put the thinest thrush washer behind the pump and reassembled again and I still have no end play.??? I think maybe the pump is bottoming out inside the input shaft which is keeping it from coming up with any end play? I say this because before putting it together this time I assembled...- tkbp4him
- Post #2
- Forum: Automatic Transmission
-
T
no end play th350
Hello, I have a 78 k10 with a "k" 4x4 housing with a "case saver" installed thats been rebuilt before that I am reusing per customer request. I have put in new bushings and clutches/steels, bearings, and thrush washers, new input shaft, and rubber seals on pistons. I put it all together which...- tkbp4him
- Thread
- Replies: 27
- Forum: Automatic Transmission
