Recent content by Mr_Ryumaru

  1. Mr_Ryumaru

    Piston recommendations for idiot who doesn't know his heads from his asphalt

    Well, checked those out and according to the store page they would make ~9.6:1. However, 500 hurts me right in the wallet, and I don't know if I can convince the boss, and she's a hard sell on truck parts as it is :D . Hard bullet to swallow Dx Out of curiosity, will those work with stock heads?
  2. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    no no, it's very light rust because the place I had it stored flooded one week without me knowing, it comes right off with emery paper. Trust me, had a damn heart attack when I opened that door
  3. Mr_Ryumaru

    Piston recommendations for idiot who doesn't know his heads from his asphalt

    Are those available in stock specs? Would they be viable given the other aspects of the build? Sorry if these seem like stupid questions, but I'm learning as I go here. Hence why I asked for advice from you guys, who know a hell of a lot more than I do, instead of buying shiny things because...
  4. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    As said earlier in the thread (a few times :P ), the block was already looked over by someone, was deemed to be in excellent condition. It doesn't even need to be bored, just honed up a bit. No ridge, no cracks, all good. Motor had less than 5k miles on it since it was rebuilt. It was pulled...
  5. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    That's been the general opinion, and that's what I'm trying to do. I know I could get away with more cam, but I think the one I've selected is a great middle ground. I'm also a freak apparently because I want a smooth idle :/ I've actually made another thread here, where I'm looking for advice...
  6. Mr_Ryumaru

    208 transfer case rebuild

    Fair enough. Don't know his setup, that's why I asked :) He might be able to, or he may not. Its worth considering. That said, I think the np208s get a bad rep. A lot of people assume because the np205 is so damn tough, that the chain driven np208 isn't, which is hardly fair to the case. There's...
  7. Mr_Ryumaru

    Piston recommendations for idiot who doesn't know his heads from his asphalt

    So I've been looking around for a set of pistons, and I've come to understand this choice should be made with advice from those who know more than me. This just a bit beyond what I know. I've work on engines, swapped engines, rebuilt engines, bolted on power mods, but this is just something a...
  8. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    Not sure which stock intakes you've seen, but the one I have is pretty bad. It's restrictive, as well as overly convoluted. I have driven a friends 454 truck before and after he had done an intake swap, and while the difference wasn't huge, the high end power while out on the highway was...
  9. Mr_Ryumaru

    208 transfer case rebuild

    https://www.midwesttrans.com/np208.html This is the site my buddy used. Don't know much more besides he got the parts he needed his rig has been on the road for a couple years since. Have you considered picking up an np205 instead? Usually pretty easy and cheap to find.
  10. Mr_Ryumaru

    Truck runs rough, help!

    Did somebody put the wrong fuel in? Maybe theres something in the tank? I almost wonder if something happened to the carb. Could you have missed a vaccum leak? Try the old spray bottle of soapy water. Check the fuel filter. Double check firing order and such. I know it's all no brainer stuff...
  11. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    Oh god the stock intake, I still have mine just in case and tbh I am legitimately dumbfounded as to how they managed even the underwhelming 230hp. I'm just glad my heads are pretty okay, or so I'm told anyways lol
  12. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    I am the engine builder :P Can't afford anyone else to do it for me. And I know the studs aren't necessary, but its a trivial cost increase, and offers no downsides.
  13. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    To all of your responses, in order lol. 1. Tread lightly :p , my baby is an '83 Ranger, and that truck is my heart and soul. All manufacturers make good vehicles. All manufacturers make bad ones. All of them have great fans. All of them have idiots. 2. I think the point he was making was that...
  14. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    Thats my mentality. If I can find or be recommended a set for around the $250 range I would be alright with spending that much.
  15. Mr_Ryumaru

    Anyone been able to nail down some specs for Mark IV 454 engines?

    Aaaaaaaaaaaaaand once again, I'm an idiot. the price of ~150 was for a set of eight, so **** it, why not. You got a link to or part number for yours, just so I can get an idea of what to look for?
See more

Latest posts

Forum statistics

Threads
42,280
Posts
912,858
Members
33,780
Latest member
joshuars
Top