Recent content by emoze

  1. emoze

    AFR GAUGE addition?

    ... https://forums.pelicanparts.com/dto_garage.php?do=viewvehicle&vehicle_id=10638
  2. emoze

    AFR GAUGE addition?

    i ran a wideband dual sensor setup on my 3.2 porsche; there are some caveats related to early sensor failures $$$ ... best to install a delay relay so the sensor gets warmed up before it gets electrically activated .. . you can prob'ly google that idea; its on the porsche forums & others ...
  3. emoze

    Fresh Air vents with factory A/C?

    on my '84 i installed old manual vents on both sides with junkyard parts
  4. emoze

    What could this random tube attached to the exhaust be?

    in CA, pre-76 is exempt from smog inspections; just remove it & enjoy the truck ... (unfortunately my 84 is not exempt)
  5. emoze

    AFR GAUGE addition?

    thinking of adding basic AFR gauge to my 84 454 with Qjet & dual exh for purpose of tuning; don't need wide-band; where should the sensor(s) be installed? (and would having one on each branch be necessary?) . (fwiw i run one on my MGB race car at the header collector point & it has been...
  6. emoze

    The wisest way to modernize a C20

    radio upgrade - about 15 yrs ago - has iPod port
  7. emoze

    The wisest way to modernize a C20

    NICE - always wanted to do that - kits were too much $$$$ tho
  8. emoze

    The wisest way to modernize a C20

    yes - enuf to get the job done - more clearance is "up high below the glass" - did it in my '84 about 25 yrs ago
  9. emoze

    Thermostat 195?

    just change it & get on with life; i've seen several new 'stats fail too soon in several cars , esp fromaftermarket brands .... buy the best known brand you can find
  10. emoze

    I guess I give up on the windows

    - since the window motors grd to door, the only hard connection of door to body is thru the hinges or door latch - seems like a good thing to try would be a grd wire twixt the door & body to rule out poor grd thru those aged components ?
  11. emoze

    Custom ignition switch not on column

    poor boy solution - the column mechanism on mine was screwed up long ago - i bo't a generic ign switch & installed it into the hole where the clock used to be - (the clock was bad anyway) - alternative was to buy a column & all the remove/install hassle that goes with - in your case the...
  12. emoze

    Cruise Control Troubleshooting and Info

    great thread! related question: my 84 CUSTOM CRUISE III tends to surge when engaged; just a little, but enuf to be annoying; throttle cable seems to be correctly taught, engine vacuum is good; (454 turbohydro 400), ideas would be welcome :) p.s. i have read this thread: Cruise control works...
  13. emoze

    headlamp warning chime device & location '84

    my 84 c20 driver manual says there is a "lights on" warning chime when Ign off; ... long long ago iirc i must have removed or disabled it ... that has cost me a dead battery a couple times :blah: where is it installed? , what is part number? , are they available? i am guessing it might just...
  14. emoze

    Wipers barley working

    - had/have similar problem - super SLOW - sometimes stop mid glass when using washer - - blows fuse - have older re-man NAPA motor - per other wiper threads here , ordered a NEW motor per advise on other thread - not yet installed (all grounds are good, so that's not the problem) (mea ciulpa...
  15. emoze

    454 kickback/dieseling after shutdown?

    does it come down to normal idle when you get off the pedal? very often - this can be caused by a throttle not closing completely - mine does that sometimes - could be idle arm adjustment; could be cruise arm or some other component is holding it open a bit; i've seen both problems &...

Latest posts

Forum statistics

Threads
45,558
Posts
986,215
Members
38,643
Latest member
Hard
Top