Recent content by carfanatic63
-
Show your daily driver
My focus st. I just need to have a stick even though I commute in Houston traffic 80 miles everyday. Fun, big enough for the kids, decent gas mileage. Has full leather recaros which makes it feel "special." Im hapoy with it. Had a Fiesta st before this which was more fun but my daughter said...- carfanatic63
- Post #557
- Forum: Other Vehicles
-
Is this a good deal?
If it rust free truly, I think that is fair if the interior is all there and nothing has been hacked up- carfanatic63
- Post #2
- Forum: Tech Discussion
-
Howdy from Houston
Hey! Another Austin in Houston with a square! Welcome! Signed - Austin from Houston with a square- carfanatic63
- Post #14
- Forum: Introduction
-
I need help and to know what this truck is worth
1k would be tops. I would honestly be happier at $500 since it doesnt have a title and has some rust if it were me. Who knows about the frame with the twist in the bed too. This might be a parts truck honestly- carfanatic63
- Post #3
- Forum: Tech Discussion
-
Painless kit 90627 - wire 901
I just put this same kit in my truck last year. Great kit. That wire goes into the interior and is a switched power wire from the ignition. You can use it to trigger a relay of some sort or connect it to another 901 wire thay goes to the engine harness and use that to trigger a relay in the...- carfanatic63
- Post #2
- Forum: Electrical & Audio
-
Model show and contest in Houston, Texas area
Man, this is in my neck of the woods (clear lake area) but Im busy this weekend. Maybe my ither plans will fall through and I can go to this!- carfanatic63
- Post #2
- Forum: Events
-
New owner of a Frankenstein K10
My guess would be its a k10 frame with a 400 swap. Original cab was rusted or damaged in some way and they put a c10 cab on it. Title is tied to the cab in most states. I know here in texas the title comes with the cab.- carfanatic63
- Post #2
- Forum: Introduction
-
C50 to C10 dash and cluster interchangeable?
I think the guage cluster is interchangeable with some repinning of the harness. Doors should swap fine too. Not sure about anything else- carfanatic63
- Post #3
- Forum: Interior
-
-
Install overhead dome light
Im not sure about the part number but you will need to fish the wire. I got a wire fisher from har or freight for the job- carfanatic63
- Post #2
- Forum: Retro-Fit & Aftermarket Accessories
-
In need of a good paint and body shop in Houston area
Im in Houston too but I dont know who I would tak my truck too since it needs some cab corners done. It seems in Houston most shops are either cheap and dirty or overpriced but quality. Its hard to find a shop that does quality work at a reasonable price. What I would do is get your truck...- carfanatic63
- Post #2
- Forum: Paint and Body
-
What did you pay for a square
Haha. Thats my old 1982 GL1100 Standard (no fairings or bags factory). That was a good cool bike. Just not "me". Sold it and bought back my vfr800 I had in college and have an st1300 for when my wife and I go out on rides too. If we have other people thay ride, we may need a motorcycle thread...- carfanatic63
- Post #45
- Forum: Tech Discussion
-
What did you pay for a square
I paid $6700 for mine in 2016. 1976 GMC C15 SWB Fleetside. I was planning on spending less for longbed but my wife and my dad convinced me to swing for a short bed since I planned on keeping it. Most shortbeds in houston sell for way too much for me so I was very happy at that price. It had an...- carfanatic63
- Post #35
- Forum: Tech Discussion
-
Clutch style fan
I would measure your current fan and order another fan in same diameter. Since SBC are everywhere, most universal fans have the bolt pattern to fit the water pump pulley. I did this when upgrading to a serpentine system on my truck while keeping mechanical fan (spins other way in serpentine set up)- carfanatic63
- Post #2
- Forum: Tech Discussion
-
Complete Re-Wire 1978 Scottsdale 4x4
I did the painless direct fit kit in my truck last year. Worth the extra money in my opinion. The manual is very thorogh and well laid out for everything and with a couple simple tools, it isnt a difficult job. Just take your time and dont rush and everything will be fine if you follow the...- carfanatic63
- Post #6
- Forum: Tech Discussion
