Search results

  1. Hillbilly

    Knocks when turning 1981k10

    Yea I’m down here in loganville send me a pic of your square? Sent from my iPhone using Tapatalk
  2. Hillbilly

    Knocks when turning 1981k10

    Hey yea they only knocks when I’m driving turning or backing out of spaces yea I don’t got no help just me and ole lady Sent from my iPhone using Tapatalk
  3. Hillbilly

    Knocks when turning 1981k10

    Hey snoots Where in georgia u from? Sent from my iPhone using Tapatalk
  4. Hillbilly

    Knocks when turning 1981k10

    Yea they look good but I’m gonna jack it up and check them out as well. This truck needed a lot when I got it but hey for 2500 what can I say. Sent from my iPhone using Tapatalk
  5. Hillbilly

    Knocks when turning 1981k10

    Yea,I know the gear box is bad. Leaks from knuckle and output shaft on box Will this cause a knock? And power steering sequels when turning?got clean full fluid and tight belt, so what else can cause the knock? Somebody else said intermediate shaft could be dry on grease.Or needle bearings...
  6. Hillbilly

    No gauge lights

    Got power at instrument fuse yea there is a grey wire on cluster connector Sent from my iPhone using Tapatalk
  7. Hillbilly

    No gauge lights

    Yes the volt and gas gauge are working.at the cluster. My #8 wire is black not grey? Sent from my iPhone using Tapatalk
  8. Hillbilly

    No gauge lights

    Still no cluster lights Sent from my iPhone using Tapatalk
  9. Hillbilly

    No gauge lights

    Hey guys my gas gauge my volts gauge work I’m running mechanical on oil and temp till I can get my sending units for this’s 400sbc now right blinker stays on when pull out light switch go out when I actually set it on right turns When light switch off it goes out blinkers work fine with no...
  10. Hillbilly

    No gauge lights

    Hey thanks for info,I’ll get on it in little bit when warms up some,so that is fiber optic man how bout that would have never known. Yea ever who wired this truck made a mess under dash but what I paid for it I’ll deal with it.Thanks to all u fellers with great info, Sent from my iPhone using...
  11. Hillbilly

    New here...Rebuilding an 81

    Welcome down here from jawga Sent from my iPhone using Tapatalk
  12. Hillbilly

    No gauge lights

    Got a new switch for headlights still no cluster lights Sent from my iPhone using Tapatalk
  13. Hillbilly

    No gauge lights

    Hey how many grounds should that cluster have ?mine is one of the bulb sockets with a round end that snaps into my ash tray holder. Sent from my iPhone using Tapatalk
  14. Hillbilly

    No gauge lights

    Got a new circuit board for my 81 still got no lights on cluster,bulbs good,sockets good,good ground (goes into ash tray housing)got running lights,head lights,brake,turn signals Dome light comes on when turn switch Old circuit board was peeling and lifted Thought that was issue.Did notice a...
  15. Hillbilly

    PCM wiper relay

    Hey what’s the deal with these things, No body’s got them auto zone orilys lmc etc. anybody got a vendor that might? Sent from my iPhone using Tapatalk
  16. Hillbilly

    What have you done to your square lately??

    I tell u what I done to my square reversed battery cables like a dumb ass Now no blinkers ,radio not working not one blown fuse I mean if the ole lady would leave me alone when I’m working on it I could think right ? I told her she got to find a hobby other than talking,anybody can relate. So...
  17. Hillbilly

    New weatherstripping

    Hey do you have to take regulators off door to get new weatherstrip in the channels?I have no help when I work on truck so I was wandering if it can be done.Have ordered new channel kit.was difficult to get old stripping out it just crumbled to pieces. Thanks guys
  18. Hillbilly

    Tag and side marker lights

    Thanks yea the tag lights are brand new side markers are not Yea I seen the little plug socket upstream, I’ll check for power to the plug,then look at sockets, hey one other thing my circuit board sheet on the gauge cluster some of the tracks have cracks on them So I have not lights for speedo...
  19. Hillbilly

    Tag and side marker lights

    These lights are not working , every other lights are, where to start troubleshooting at?
  20. Hillbilly

    What have you done to your square lately??

    Thanks buddy,that’s what I figured come out better to just replace,now wouldn’t I already have a frame brace? Or is that an add on u do for additional support? Sent from my iPhone using Tapatalk
  21. Hillbilly

    What have you done to your square lately??

    How big a deal is it to rebuild your steering gear box?mines leaking at the input shaft I know seal kits are cheaper than a rebuilt Gear but I’m looking for the best way to fix it with the longest durability. It’s a 81 Scotty k10 nice truck just don’t wanna turn smooth With that problem plus...
  22. Hillbilly

    Instrument cluster/ speedo

    Yea mine stay on after I crank the truck The ends on the speedo are more round than square but it’s brand new and was matched for my truck so any way . Sent from my iPhone using Tapatalk
  23. Hillbilly

    Instrument cluster/ speedo

    They are on all the time Sent from my iPhone using Tapatalk
  24. Hillbilly

    Instrument cluster/ speedo

    Why would all the clusters lights be on? Short to ground maybe? Put in new speedo cable still does not work,cable I bought looks like round ends on both male connectors. Shouldn’t they be more square like the transfer gear housing? Sent from my iPhone using Tapatalk
  25. Hillbilly

    New to group

    Thanks Actually paint is little runny in places but I’m not complaining. I agree about the wheels but not priority right now. Other little things gonna fix Go dawgs Sent from my iPhone using Tapatalk

Latest posts

Forum statistics

Threads
42,137
Posts
909,894
Members
33,634
Latest member
prenrag
Top