Search results

  1. O

    What have you done to your square lately??

    just make sure to get a 96-97 pcm if you dont want to have vats programmed out. http://vid225.photobucket.com/albums/dd79/oopsman_09/20160530_161333_zpscrajpdja.mp4 here is a link to my engine running. I cant figure out how to embed the video...fail
  2. O

    What have you done to your square lately??

    no just went to lt1swaps.com and read through the wiring pinout. its not my first fuel injection swap so i had an idea on where to start. I also have the entire engine and trand harness (uncut) and the under dash harness. But if you hook up the engine harness to the engine. then just plug your...
  3. O

    What have you done to your square lately??

    got a vortec 350 wired up for standalone. just need trans, fuel system and driveline modified.
  4. O

    What have you done to your square lately??

    pulled a harness and ecm at the pick a part. tbi swap to follow.
  5. O

    How Will My Square Body Look With XX Lift and XX Tires?

    stock 81 c10 31x10.50R15
  6. O

    What have you done to your square lately??

    put new tires on the old truck. 31x10.50R15 much better than the old tires. used tires federals on the rear and khumo's on the front but they are the same tread pattern(or extremely close) and are all pretty much new. and 2 old ones for comparison
  7. O

    propane in a 84 6.2

    propane will give you a boost in fuel economy but really only in a turbo application. propane is a higher octane than diesel so it will burn slower and longer causing the diesel to burn more thoroughly. therefore getting you better mpg's and increased power.
  8. O

    propane in a 84 6.2

    propane injection is like nitrous on a gasser except its for low end. hes not replacing diesel with propane just injecting it.
  9. O

    What have you done to your square lately??

    swapped out transmissions and converted brakes to hydroboost.
  10. O

    Cool Mirror Swap

    i like it but dont like the wing window delete.
  11. O

    Cool Mirror Swap

    they are from a duramax
  12. O

    ? about my 700R4 swap

    you could run it without lockup but it would be nice for highway mileage. there is a way to do it with an oil pressure switch so it locks in overdrive that is way cheaper than a controller if your ok with minor wiring. and if your ok using a toggle to turn it off for slow city driving.
  13. O

    Will 20 Gallon Tanks Bolt In?

    my lwb has 12 gallon tanks :(
  14. O

    suburban driveline vs truck driveline?

    ahh i see. could i cut the hump out of the burb and use it in the truck
  15. O

    suburban driveline vs truck driveline?

    was beginning to wonder if anyone was going to reply to this lol.
  16. O

    suburban driveline vs truck driveline?

    i would be running both trans and t-case.isnt the 81+ truck cabs the same? i know the 73-80 trucks had the bolt in 4x4 trans hump. plan was to turn this truck into a 4x4. was just wondering if it was at all feasible. as for someone needing a 4x4 burb i would be more than willing to sell a...
  17. O

    Brakes on differentials?

    rockwell axles
  18. O

    Dodge Dana 60 up front

    i think he means coil spring to leaf spring
  19. O

    suburban driveline vs truck driveline?

    Not the usual question. I know the suburban has a 2" shorter wheelbase thus a 2" shorter driveline. however i aquired an 89 1/2 ton 4x4 burb whith a good 700r4. My question is if i put this trans and t-case into my 81 1/2 ton 2wd what driveline should i use? I know mine wont work, and i know i...
  20. O

    rear heat

    has anyone retrofitted rear heat into a suburban blazer or crew cab?
  21. O

    Anyone got Stacks?!?

    i always heard under body exhaust on trucks called weed burners. and by trucks i mean big rigs. so maybe the farm thing is somewhat true.
  22. O

    Where is this guys build thread...?!?!

    i wanna see more of this
  23. O

    moving 4x4 shifter to driver side.

    see now if only i could find a build thread on such a thing.
  24. O

    moving 4x4 shifter to driver side.

    ive seen some guys make their own cable kit but all on off road buggies or something where the shifter is just a steel lever. guess using an oem style shifter wouldn't be any different. even if you had to fab up a cable bracket.
  25. O

    moving 4x4 shifter to driver side.

    that would come with ifs so no thanks. besides its more fun to build one. and whats wrong with having a few luxuries in an old truck.

Latest posts

Forum statistics

Threads
42,167
Posts
910,461
Members
33,660
Latest member
1987R10Man
Top