Recent content by Hillbilly
-
Knocks when turning 1981k10
Yea I’m down here in loganville send me a pic of your square? Sent from my iPhone using Tapatalk- Hillbilly
- Post #12
- Forum: Lifted & Off-Road Systems
-
Knocks when turning 1981k10
Hey yea they only knocks when I’m driving turning or backing out of spaces yea I don’t got no help just me and ole lady Sent from my iPhone using Tapatalk- Hillbilly
- Post #11
- Forum: Lifted & Off-Road Systems
-
Knocks when turning 1981k10
Hey snoots Where in georgia u from? Sent from my iPhone using Tapatalk- Hillbilly
- Post #8
- Forum: Lifted & Off-Road Systems
-
Knocks when turning 1981k10
Yea they look good but I’m gonna jack it up and check them out as well. This truck needed a lot when I got it but hey for 2500 what can I say. Sent from my iPhone using Tapatalk- Hillbilly
- Post #3
- Forum: Lifted & Off-Road Systems
-
Knocks when turning 1981k10
Yea,I know the gear box is bad. Leaks from knuckle and output shaft on box Will this cause a knock? And power steering sequels when turning?got clean full fluid and tight belt, so what else can cause the knock? Somebody else said intermediate shaft could be dry on grease.Or needle bearings...- Hillbilly
- Thread
- Replies: 12
- Forum: Lifted & Off-Road Systems
-
No gauge lights
Got power at instrument fuse yea there is a grey wire on cluster connector Sent from my iPhone using Tapatalk- Hillbilly
- Post #15
- Forum: Gauge, Speedo & Instrumentation
-
No gauge lights
Yes the volt and gas gauge are working.at the cluster. My #8 wire is black not grey? Sent from my iPhone using Tapatalk- Hillbilly
- Post #13
- Forum: Gauge, Speedo & Instrumentation
-
No gauge lights
Still no cluster lights Sent from my iPhone using Tapatalk- Hillbilly
- Post #11
- Forum: Gauge, Speedo & Instrumentation
-
No gauge lights
Hey guys my gas gauge my volts gauge work I’m running mechanical on oil and temp till I can get my sending units for this’s 400sbc now right blinker stays on when pull out light switch go out when I actually set it on right turns When light switch off it goes out blinkers work fine with no...- Hillbilly
- Post #10
- Forum: Gauge, Speedo & Instrumentation
-
No gauge lights
Hey thanks for info,I’ll get on it in little bit when warms up some,so that is fiber optic man how bout that would have never known. Yea ever who wired this truck made a mess under dash but what I paid for it I’ll deal with it.Thanks to all u fellers with great info, Sent from my iPhone using...- Hillbilly
- Post #8
- Forum: Gauge, Speedo & Instrumentation
-
New here...Rebuilding an 81
Welcome down here from jawga Sent from my iPhone using Tapatalk- Hillbilly
- Post #12
- Forum: Introduction
-
No gauge lights
Got a new switch for headlights still no cluster lights Sent from my iPhone using Tapatalk- Hillbilly
- Post #6
- Forum: Gauge, Speedo & Instrumentation
-
No gauge lights
Hey how many grounds should that cluster have ?mine is one of the bulb sockets with a round end that snaps into my ash tray holder. Sent from my iPhone using Tapatalk- Hillbilly
- Post #3
- Forum: Gauge, Speedo & Instrumentation
-
No gauge lights
Got a new circuit board for my 81 still got no lights on cluster,bulbs good,sockets good,good ground (goes into ash tray housing)got running lights,head lights,brake,turn signals Dome light comes on when turn switch Old circuit board was peeling and lifted Thought that was issue.Did notice a...- Hillbilly
- Thread
- Replies: 16
- Forum: Gauge, Speedo & Instrumentation
-
PCM wiper relay
Hey what’s the deal with these things, No body’s got them auto zone orilys lmc etc. anybody got a vendor that might? Sent from my iPhone using Tapatalk
