Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Ricko1966's latest activity
R
Ricko1966
reacted to
Zelph's post
in the thread
Adding 4WD, where does the shifter go?
with
Like
.
700R4 with a NP241. From the firewall to the shift plate From driver side From passenger side
May 6, 2024
R
Ricko1966
replied to the thread
What Engine Do I Have
.
Try asking for a fuel pump for a 1986 c10 305 automatic. They should hand you a 3 port pump
May 6, 2024
R
Ricko1966
replied to the thread
Cross pin bolt snapped
.
Heat it with propane and don't use much force if you are using an EZ OUT if you break the EZ Out you can't drill it out. If it doesn't...
May 6, 2024
R
Ricko1966
reacted to
fast 99's post
in the thread
Cross pin bolt snapped
with
Like
.
Get a GOOD new left-hand drill bit or 2. If you're lucky drill will stick and back the piece out. That worked many times for me on...
May 6, 2024
R
Ricko1966
replied to the thread
What Engine Do I Have
.
Vortecs came out in 96, so,don't get your hopes up.
May 6, 2024
R
Ricko1966
reacted to
gmbellew's post
in the thread
Poping fuses when ac controls are on
with
Like
.
I am not clear on when the issue started, when parts were replaced, or if they corrected the issue. But seems likely there is a short to...
May 5, 2024
R
Ricko1966
replied to the thread
Poping fuses when ac controls are on
.
Digital multi meter. Take a light socket for a 194 bulb,crimp a male spade connector on each of the wires to the socket,remove the...
May 5, 2024
R
Ricko1966
replied to the thread
Verify defect fuel sending unit
.
IMHO pulling the bed or cab to change a tank is a bunch of extra work. I always have to drill the heads off the bed bolts. I'd unbolt...
May 5, 2024
R
Ricko1966
replied to the thread
What Engine Do I Have
.
If it's got a manual pump you will want another manual pump if its 2 port get another 2 port if it's 3 port get another 3 port. I...
May 5, 2024
R
Ricko1966
replied to the thread
Proportioning valve problems
.
This ^^^^ this is just one reason I don't change parts,any parts,just to change parts. I do not adhere to the it was old so I just went...
May 5, 2024
R
Ricko1966
reacted to
fast 99's post
in the thread
Proportioning valve problems
with
Like
.
Not the first time I have heard about them leaking. Offshore parts are questionable. Try to find used OEM. Seems to be a lot of these...
May 5, 2024
R
Ricko1966
reacted to
idahovette's post
in the thread
Scissor Jack
with
Like
.
OK, I'm confused.....where were/are we????......pinching....... going bigger.......so many questions....auto....manual???????
May 5, 2024
R
Ricko1966
reacted to
Doppleganger's post
in the thread
What new tools have you got lately?
with
Like
.
Local hardware still carries Irwin (USA) taps and thread dies. I buy them 1-2 at a time. They hold up quite well. Like most of...
May 5, 2024
R
Ricko1966
replied to the thread
Help: 85 305 Suddenly Stalling in Gear
.
There is something special about that one. It should be esc. The 2 biggest failure points are the esc. controller and the module. In my...
May 5, 2024
R
Ricko1966
reacted to
nvrenuf's post
in the thread
FRONT DIFF SWAP
with
Like
.
If you can find a 78-79 Ford leaf spring axle (D44 or D60) it’s a direct bolt in, anything else will require fabrication.
May 5, 2024
Latest posts
Greetings From Canada. 1987 Chevrolet V10 4x4 350 TBI
Latest: Strick
2 minutes ago
Introduction
New guy here from Wyoming.
Latest: Strick
9 minutes ago
Introduction
Newbie
Latest: Strick
11 minutes ago
Introduction
74 C10 windshield washer nozzle location
Latest: SirSmartyPants
31 minutes ago
Exterior
T
454 peanut head cam change fun.
Latest: txaggie
46 minutes ago
Engine & Performance
Forum statistics
Threads
42,342
Posts
914,027
Members
33,845
Latest member
aaron06
Members
Top