Search results
-
Help with ignition lock removal - 1984 M1010
Thanks for the info. I almost pulled that but was afraid to do damage. I did watch a video where they just grabbed it with a pair of needle nose pliers and pulled it out so I will certainly try that. I figured there were wires connected to the back of it. The truck is about 50 miles away so...- ballencd
- Post #3
- Forum: Tech Discussion
-
Help with ignition lock removal - 1984 M1010
Good evening, I am having an issue with my ignition lock removal. The vehicle is a 1984 M1010 (Military Ambulance). All military trucks are keyed alike so in the interest of security I am trying to change out the ignition key lock and door locks. I have done this before on a M1009 (Military...- ballencd
- Thread
- Replies: 3
- Forum: Tech Discussion
-
-
Question on where to get a 6.2 fuel line feeding the lift pump?
I think I have a leak in the supply hose just before the lift pump on my 1984 K30 with a diesel 6.2 engine. It is molded and I can't find one anywhere. Any ideas?- ballencd
- Thread
- Replies: 3
- Forum: Tech Discussion
-
Will this work with 35s?
My 91 Suburban is running 17x8.5 Method MR701 wheels and Nitto Terra Grappler G2 - LT285-75R tires....34" tall and about 11" wide and I have not had any rubbing after tapping in the back of the front fenders with a hammer very lightly. I don't run it off road but it is a daily driver. The...- ballencd
- Post #21
- Forum: Suspension, Steering & Brakes
-
-
-
Method 701 milled aluminium rims
I have three kids and get lost in their world if something is not broken. Here's more info on the wheels and brakes even if it is late. The wheels I put on were Method 17x8.5 MR701 +0 offset with 6x5.5 lug spacing. These will not fit a stock suburban without wheel spacing out about 1/2" or...- ballencd
- Post #26
- Forum: Wheels and Tires
-
Vacuum switch, break switch, and wiring for 700-R4
Just realizied that I never responded to this. Thanks for the info. Do you know if there is a way to light a lamp when it is in lockup and/or in OD? -
Old dual tank location, what do do with space?
I have a suburban with the 41 gallon tank in the rear and have thought I wanted to put two saddle tanks on the sides for more distance and possibility or bringing diesel or gas home for other vehicles or the tractor. The ability to pump it out, pump it into a different tank or use a different...- ballencd
- Post #14
- Forum: Paint and Body
-
Vacuum switch, break switch, and wiring for 700-R4
Slightly off topic but how do you tell when the lockup on a 700R4 is engaged? 1991 Suburban -
Method 701 milled aluminium rims
The tie rod end hit the inside of the wheel. Of course the dealer said they fit even thought they did not. I was also in the process of changing the brakes and could tell that that would fix it so I dropped it with the wheel dealer. When putting Hummer brakes on the axle the rotor was removed...- ballencd
- Post #18
- Forum: Wheels and Tires
-
Method 701 milled aluminium rims
I did have to put Hummer brakes on it to get them to fit.- ballencd
- Post #16
- Forum: Wheels and Tires
-
Method 701 milled aluminium rims
I like the black spoke on a square.- ballencd
- Post #15
- Forum: Wheels and Tires
-
2.5 Rockwells is anybody running these
What about putting your Suburban body on a M35 frame? That would be the easiest thing to do and probably cheapest too...?- ballencd
- Post #9
- Forum: Off-Roading
-
What have you done to your square lately??
I removed the "1500" logos on the doors. And started cleaning up the white corrosion coming thru the paint on the rear floor. -
Engine problem
I'd start with a full tune up before I messed with the carb. You need to know where you are starting from.- ballencd
- Post #14
- Forum: Introduction
-
Which manual transmission?
I'm looking at the TR-4050 for about the same application. Not cheap but they are still building them and they can handle the torque of a 6.2.- ballencd
- Post #6
- Forum: Manual Transmission & Clutch
-
Oil Pressure Goes to Zero!
The gauges have not failed again since the wire wiggling. The engine only has about 130K on it but I do run Lucas and 15-40 Rotella in it already. I think is was a loose wire.- ballencd
- Post #34
- Forum: Engine & Performance
-
Oil Pressure Goes to Zero!
There is no mechanical interference on the wire. Picture looks like they touch but they are far apart. Interesting......today I pulled the dash and wiggled all the wires, moved the tach wire away from the rest, reseated a few wires and the problem for now has gone. I reinstalled the dash and...- ballencd
- Post #31
- Forum: Engine & Performance
-
Oil Pressure Goes to Zero!
That means I have to buy a new gauge. I have another electrical gauge that I could try which I can connect directly to the battery and remove a wiring issue. I will start there.- ballencd
- Post #26
- Forum: Engine & Performance
-
Oil Pressure Goes to Zero!
All other gauges work fine, no changes.- ballencd
- Post #24
- Forum: Engine & Performance
-
Oil Pressure Goes to Zero!
Would that fail only when the engine is warm and its revved up in REVERSE with the brake on? Wouldn't it fail all the time it was warm and revved up....FORWARD or REVERSE or NEUTRAL.....? I think I can test it via resistance sending unit to ground and it should fail if that's what it is but I...- ballencd
- Post #21
- Forum: Engine & Performance
-
Oil Pressure Goes to Zero!
The rats used to chew up everything but we have two cats that keep them away now. I have not seen a mouse or rat for several years.- ballencd
- Post #19
- Forum: Engine & Performance
-
Oil Pressure Goes to Zero!
Yes, gauge is electric. Caveat of the broken or shorted wire is that they are all new, have been inspected and look good. No evidence of mice or rats. Not near the exhaust as it is several inches away at the filter and in convoluted tubing. There is also the issue that it only does this when...- ballencd
- Post #18
- Forum: Engine & Performance
