Search results
-
What have you done to your square lately??
Been awhile hopefully everyone is doing good, today I loaded up the square and went to my buddy's place that has a TTspec truck with the ls3 I built to check it out and it sounds awesome -
What have you done to your square lately??
Put in some work hauling the new to me camper -
What have you done to your square lately??
This is what I'd do to it lol -
What have you done to your square lately??
Got the under bed boxes mounted little more room for my junk -
What have you done to your square lately??
Actually I Tested them used them on a few projects a good crimp or actual solder works better but they will work -
What have you done to your square lately??
Those work ok if you do a lineman splice and add extra heat shrink -
What have you done to your square lately??
Started making the roof rack -
What have you done to your square lately??
I really like how that turned out -
What have you done to your square lately??
After nearly 50 years of service I have retired the old school red lights some more changes coming that ment they had to go -
What have you done to your square lately??
Curious what's y'all's opinion on bronze vs paper fuel filter for the qjet I run one filter just before the lift pump and one after the mechanical pump(I plan one deleting but was some I set up so I can see the fuel flow under hood)my filter inside the carb is probably about due so thinking... -
What have you done to your square lately??
Grant Wood grain I'm gripping -
What have you done to your square lately??
Been busy working on other projects I did get some new tool boxes to mount under the flatbed I have already started making the 3x6 frame rails that will fit under the box/gas tank and run along the side of the cab few other changes coming to the rig after I get my jeep finished up -
What have you done to your square lately??
6x9s to replace the 4 6in speakers I have screwed in to plywood shoved into the corners behind the seat lol I think when I get to doing something with the center console I'll add a speaker on each side factory non radio truck so I think I'll add some speakers under the dash pad projects for... -
What have you done to your square lately??
Got a topside creeper a few months ago major back saver and just makes wrenching on the trucks so much easier -
What have you done to your square lately??
Checked the fluids and put a few psi in the front tires then went down and got the LS3 back from the machine shop -
What have you done to your square lately??
So Something like that for my 75 would be great nice work -
What have you done to your square lately??
First attempt at tint not great but not too terrible no bubbles but my trimming needs work still have to do the back window and got plenty to redo the fronts later I think my original idea to pull the window out will make the trimming easy and perfect fit -
What have you done to your square lately??
The condenser will most likely net the biggest change especially if it's a tube and fin style the flat serpentine style will work slightly better and typically works for both r12-r134a the more modern parallel flow will work best with r134-r1234 we didn't mess with swapping orafice tubes to much... -
What have you done to your square lately??
@Goldie Driver make shure it's got a good fan clutch and seal up the condenser/rad/fan shroud with foam rubber etc. -
What have you done to your square lately??
If your using a machine to fill there is high chance the refrigerant is contaminated when I ran a a/c shop we used a vacuum pump and a scale with a fresh tank of refrigerant only used the machine for evac and testing -
What have you done to your square lately??
I seen worse but that's not good need to flush the evap and lines drain the compressor and change the accumulator, if your running r134 you need to swap condensers if you have the tube style it won't cool right I'm assuming your doing this because it's not cooling correctly don't forget you... -
What have you done to your square lately??
Haha yes I know but all the videos I see cut the tint on the outside then transfer to inside -
What have you done to your square lately??
Thanks, I watched a few videos on it, the fronts Im considering pulling out of the truck and doing them the back will have to be cut and installed from inside since the headache rack is in the way -
What have you done to your square lately??
First time messing with tint so I got a cheap roll in case I mess it up -
What have you done to your square lately??
Some cheap sound and thermal insulation for the 83 thinking it will help keep some of the heat out of the cab from the big block just need to get a fresh rubber floor also got some cheap 5% ceramic tint trying to keep some of the 90+ heat out of the truck
