Search results
-
Show me your Tire Size on 20" wheels
THX and want to see more on tire size set up to see what it look....for now i'm in the range of 295-45-20 rear and 255-45-20 in front- TPISly-C10
- Post #3
- Forum: Wheels and Tires
-
Show me your Tire Size on 20" wheels
Show me your Tire Size on 20" wheels! i plan to change my wheel set up and i want to see yours! :D- TPISly-C10
- Thread
- Replies: 21
- Forum: Wheels and Tires
-
91’ suburban 6.0 ls swap
6L/4L80E 2x4 in mine and man i love this engine, good power, good milage lot of fun for $500 (engine only at Kenny U Pull) :D- TPISly-C10
- Post #22
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Steering Column Swap
don't know about the '73 but on mine i swap a 1989 Suburban in my '86 and it was bolt on! :)- TPISly-C10
- Post #2
- Forum: Suspension, Steering & Brakes
-
Door and dash aluminum trim and emblems resto questions
i fit on my door panel 2" aluminium plate, brush be me! :)- TPISly-C10
- Post #16
- Forum: Interior
-
1984 C20 7.4L/454 Factory Spec Upper Radiator Hose with Brass 4 ROW OEM Radiator
on mine i just use en pluming reducer to fit my small LS hose! ;)- TPISly-C10
- Post #10
- Forum: Tech Discussion
-
Gauge Cluster Swap
yes but so much easy to have the fuel gauge in the tach to fit in place on the big fuel unit! ;)- TPISly-C10
- Post #22
- Forum: Electrical & Audio
-
Gauge Cluster Swap
i try to find a C60-C70 cluster for tach with small fuel gauge! :)- TPISly-C10
- Post #13
- Forum: Electrical & Audio
-
-
LS Swap adding OEM cruise control
in fact those unit are very stand alone the "J" wire don't really need to be connect to the ECM, if you have DBC and have access to a VSS and TCC connection any EFI will work! :) this is quote from a old truck forum: "I made this diagram for Clyde65, but thought others might be able to use it...- TPISly-C10
- Post #9
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
LS Swap adding OEM cruise control
yes find out that 2 green/white wire coming out from the ECM and they close from each other so its easy to be confuse so problem solve...i slice the rong one!! now everything work juste fine and i'm so happy to have this fonction on my old truck! :) just to know....i used a 1992 Olds...- TPISly-C10
- Post #8
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
LS Swap adding OEM cruise control
iv done all the wiring myself save me lots of $$$..it so easy for me since i'm a ex- auto electrical tech (long long time ago lolll) :D- TPISly-C10
- Post #7
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
LS Swap adding OEM cruise control
i found the problem...i slice the rong green/white wire from the ecm to have VSS signal! ;)- TPISly-C10
- Post #6
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
-
LS Swap adding OEM cruise control
somebody here got a LS Swap and adding OEM cruise control? try to do mine and after all the wiring and part install it doesn't work! Check all my power source, ground, got a good working stalk with all working switsh, TCC hook up good, brake light source good, VSS hook up at my electronic...- TPISly-C10
- Thread
- Replies: 14
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
LS & Vortec Swap to 90-91 VSS Electronic Gauge Cluster
If you don't have a Suburban cluster ...G-Van 90+ can do the job if you can swap the square face plate without braking the needle...and is cheaper at the junkyard ($35 ) :)- TPISly-C10
- Post #41
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
Excess Rear End Backlash
mine was bad too ..change unit for posi at the same time :)- TPISly-C10
- Post #14
- Forum: Differential & Driveline
-
-
Got to a project I was putting off... Swapping to a tilt column
was lucky to find one at the junckyard from a 1989 Suburban ($50) was a easy swap since my 1986 was the same wiring..and got cruise fonction for my future plan to install one on mine! :) tilt is u must for me..so much easy to get in and out! ;)- TPISly-C10
- Post #18
- Forum: Tech Discussion
-
One side sagging
since mine got now the good stance..my rear feel a bit to much low...so i buy back some OEM style rear shackle to get the right stance in back! man my ride confort is so much better...my vibration that i have to figure to (pinion angle setting) sime to be good! i never put again those drop...- TPISly-C10
- Post #13
- Forum: Suspension, Steering & Brakes
-
One side sagging
buy a 1" rubber spacer for the front left coil! now it sit right! 1/4 inch in front and 0 even hight in back (before was 1-1/4 in front and 3/4 in rear) i'm happy! :D- TPISly-C10
- Post #8
- Forum: Suspension, Steering & Brakes
-
One side sagging
i see in front the sag driver side! :)- TPISly-C10
- Post #7
- Forum: Suspension, Steering & Brakes
-
One side sagging
i think i'm gonna look and mesure those old leaf at back! thx :)- TPISly-C10
- Post #6
- Forum: Suspension, Steering & Brakes
-
One side sagging
my front coil are brand new too..but my rear leaf is old thy for the input! ;)- TPISly-C10
- Post #5
- Forum: Suspension, Steering & Brakes
-
