Search results

  1. rich weyand

    Rebuilding 350

    Do you know what size chambers the heads have? And which size valves? What's the part number on the end of the heads? http://www.pbm-erson.com/UserFiles/Documents/Product/Casting-Guide-World-Iron-Heads.pdf
  2. rich weyand

    Cam Help

    The first several groups of hits here have lots and lots of discussion. https://www.google.com/#q=weyand+cam+350&* Short story: cam it for torque, not horsepower.
  3. rich weyand

    Timing is way off...

    Last paragraph first. That just means the disti was stabbed in the wrong place to get the normal 5:00 position. No issue there. Let me understand. You set the timing to 12* BTDC with the vacuum disconnected. With the vacuum back connected, you read between 30 and 38 degrees BTDC at idle...
  4. rich weyand

    500cfm edelbrock or 600 cfm holley??

    I can't disagree with any of that.
  5. rich weyand

    500cfm edelbrock or 600 cfm holley??

    :Insane:
  6. rich weyand

    Edelbrock 1406 failed emissions

    De nada. Thanks for letting me know. Curious also about what your gas mileage does.
  7. rich weyand

    Carburetors

    The throttle plate on the secondaries of the 1406 is mechanical, but there is a vacuum-operated air door above it, so the effect is the same. The best carb to run on the street is a Qjet, assuming you have one set up for the application. Don't just get one off the shelf that isn't...
  8. rich weyand

    500cfm edelbrock or 600 cfm holley??

    Yeah. Everybody always wants to over-carb, and they get worse performance and worse mileage from the more expensive carb. And then the next step is not to tune it properly with an A/FR meter, because it's too expensive, then bitch about how the new carb performs. A 305 at 5000 rpm will pump...
  9. rich weyand

    500cfm edelbrock or 600 cfm holley??

    Yes?
  10. rich weyand

    500cfm edelbrock or 600 cfm holley??

    A normally aspirated 305 can't pump more than 450 cfm at 5000 rpm, so either will do fine for volume. Some people say the Edelbrock is better for street use, the Holley for track use. Most carbs are more efficient running at a higher percentage of their rated cfm, because the stack velocity is...
  11. rich weyand

    Electric fan Conversion

    Nope. The stock heads on the 350/260 crate engine, which I think are 882s. For lots of torque in the bottom, heads aren't really an issue. The flow rate is not high enough at those rpms.
  12. rich weyand

    Electric fan Conversion

    I wouldn't put Ford parts on a Chevy, but maybe that's just me.
  13. rich weyand

    Cold Starting Issue

    Push it once and hold it for a couple seconds, then release the gas and hit the key. When my choke pivots get dirty, the plate doesn't slam shut, it eases shut. You may not be giving it enough time. Spraying the choke plate pivots and the choke rod pivots with a little penetrating oil (like...
  14. rich weyand

    Electric fan Conversion

    Yes, but minor. Maybe 1/2 mpg. I got my K10 up to a solid 10 mpg on very short trips (~5 miles each way) of city driving, the first 2 miles of which are usually with the NP203 in LOC to keep the rear main output shaft bearing reservoir filled. This drive also includes the 60' high, 13* hill...
  15. rich weyand

    Electric fan Conversion

    I wrote mine up on another forum. Not much to it for an sbc, which usually run pretty cold. I don't tow or plow, so I didn't go with ducted. So here's a simple setup. http://forum.73-87chevytrucks.com/smforum/index.php?topic=27899.0
  16. rich weyand

    cam break in oil/adative

    After the first 3000 miles you can go to full-synth. I run Mobil1 10W30 with half a bottle of ZDDPPlus every oil change. For break-in I would go with non-synth 10W30 with Comp Cams break-in additive, and use the assembly lube when putting it together.
  17. rich weyand

    Affordable engine replacement?

    First, it needs to say "wideband". The last one above doesn't in the title, but it does in the description. Second, you don't need a gauge. You are going to set it up once and forget it. That said, the gauge units appear less expensive than the box-type units. Third, you don't need...
  18. rich weyand

    305 camshaft selection

    From the thread I linked above: "A "lope" means the engine is uncomfortable running at idle. So how much torque are you going to have at 1000-3000 rpm? A lope in a V-8 is the natural result of being cammed for horsepower at 5000 rpm and above. How often do you drive at 5000 rpm? If you're a...
  19. rich weyand

    305 camshaft selection

    Well, I don't know anything about rollers. Flat-tappet stuff, sure. Read this thread for starters, beginning with this post: http://www.gmsquarebody.com/forum/showthread.php?t=16990&page=3
  20. rich weyand

    quick easy-ish 350 upgrades

    This is what a 350 cammed for the street sounds like. 300+ ftlbs of torque at 1000 rpm, 420+ ftlbs at 2500 rpm. https://www.youtube.com/watch?v=P8w-DPV5_Xw
  21. rich weyand

    quick easy-ish 350 upgrades

    Yeah, I have to say it so often that I've thought of putting it on a function key. "I'd really like a little lope." <F3> :)
  22. rich weyand

    Backfire on one side

    The time to suspect something is when that's the thing you worked on. Pretty easy to check.
  23. rich weyand

    quick easy-ish 350 upgrades

    First, a "lope" means the engine is uncomfortable running at idle. So how much torque are you going to have at 1000-3000 rpm? A lope in a V-8 is the natural result of being cammed for horsepower at 5000 rpm and above. How often do you drive at 5000 rpm? If you're a racer, ALL of your driving...
  24. rich weyand

    quick easy-ish 350 upgrades

    Well, there's several levels of utility there: You M-U-S-T replace the lifters when replacing the cam. You should replace the springs when putting in a 12-235-2. It's probably best to put new oil seals in it while you have it apart. It's a good idea to replace the timing set while you have it...
  25. rich weyand

    quick easy-ish 350 upgrades

    If you google my last name with 12-300-4 and 12-235-2, you get lots of cam discussions. Look at google response 1,2,3, and 6: https://www.google.com/#q=weyand+12-300-4+12-235-2

Latest posts

Forum statistics

Threads
45,947
Posts
996,623
Members
39,141
Latest member
jbwhitford
Top