Search results

  1. R

    Front spring question

    Homemade version if you make one. Drill the heads of the bolts with a large bit to make a divot on the heads. to keep from walking off the ball joint studs. Look at the one in the pic,a drill bit works fine. Use 1 short bolt 1 long bolt ike 1/3 and 2/3 with just enough length to fit between...
  2. R

    700R4 Transmission Questions/Issues

    The only symptom would be a small fluid leak.
  3. R

    Front spring question

    This is what I was telling you how to make out of 2 bolts and a coupling nut...
  4. R

    Good Ospho (phosphoric) and epoxy Test

    Some of the paint over rust products use tannic acid as part of the process the tannic acid needs some iron oxide to work( anyway that's what I was told by one of the manufacturers a decade or so ago when I was researching it. I'd ask the manufacturer for more info,not us.
  5. R

    700R4 Transmission Questions/Issues

    Do you have a correction arm on the carb,and the correct bracket on the manifold?
  6. R

    Front spring question

    I'd try 2 bolts screwed into a coupling nut. Use them as a wedge to push on the lower ball joint stud leave the ball joint nut on but back way off. Unscrew the bolts from the coupling nut putting pressure on the ball joint stud,then smack the side of the steering knuckle with a hammer,right next...
  7. R

    Front spring question

    Or a fat passenger. Everybody leaves that one out.
  8. R

    What new tools have you got lately?

    That's for shock absorbers, and in my opinion would be a PITA on a distributor. I put the wrench on as far clockwise as I can,rotate as far counter clockwise as I can. Move my distributor twist the wrench back. With the ratcheting one you've have to pull it back out, reverse direction,and fish...
  9. R

    Good Ospho (phosphoric) and epoxy Test

    He said spi says not use acid under epoxy,I don't think that's right. I belive SPI only recommends ospho and only when directions for using it are followed completely,which is what I think that second test was. I'll look and see. Yep Ospho is the only phosphoric acid treatment,SPI recommends.
  10. R

    Tailgate security solution needed

    Install this in the tail gate like a door lock,attach 1 latch pull rod to it,so you have to turn it to pull one latch in,lift the handle for the other. Or use an electric pull solenoid with a reed switch or keyed electric switch,to oull 1 latch rod. It would make opening a 2 handed operation...
  11. R

    12 bolt Rear axle ratio?

    First 2 ka should be 3.55
  12. R

    Rust coating for fill neck

    I'd clean it and epoxy prime it.
  13. R

    81 K10 fuse panel layout

    Sorry,forgot to look. Not home right now. Sorry
  14. R

    Engine runs rough and backfires after warm-up

    Okay does it run okay cold? Cold it's in open loop. Warm it's in closed loop,I'd start by testing my sensors.
  15. R

    Engine runs rough and backfires after warm-up

    Yes you need to disconnect the set timing connector. When,how and why did it start backfiring? Have you actually checked fuel pressure?
  16. R

    Why can’t I post wheels for sale?

    I meant if he said hi to everyone in introductions he could be at 50 posts in 10 minutes.
  17. R

    Dual Battery

    Remove the trigger wire from the isolator,if everything still stays on toggle on or off,then the isolator is shot. Hook up like# 33 for now no jumper wire needed. If and when you have a good battery in spot #2 I'll get you a relay number and walk you through wiring it up. Should cost about...
  18. R

    Dual Battery

    Was this with B1 connected to unused terminal on the isolator?
  19. R

    Stereo

    Head unit Grey and white are front speakers,purple and green rears. Black stripes are speaker negatives.red is keyed power,yellow is constant power,blue is the amp trigger black is ground. I have no idea about tge rest of that mess.more and better pics maybe would help. I have no idea what...
  20. R

    Dual Battery

    Can you charge and test B2? If not. For now pull all negative wires from b2 and ground them. Run 16 gauge with 20 amp fuse to unused solenoid post. Do your lights etc work with toggle. If no jumper wire big post 1 to big post 2 for now.We can go further when you get Bat2 tested or replaced. But...
  21. R

    Dual Battery

    I mean was b2- disconnected while you ran the truck? Never mind you answered me.
  22. R

    Dual Battery

    Is the negative post still discoonected?
  23. R

    Why can’t I post wheels for sale?

    Go to search,type introductions. Say hi to everyone.Problem solved.
  24. R

    Front spring question

    Or he could get a fat passenger. Just thinking out loud here.
  25. R

    What new tools have you got lately?

    I got a Harbor Freight tamper proof screwdriver,it started out as regular screwdriver. I was in a jam needed a Phillips screwdriver,right now, there was a Harbor Freight in eyesight. Now I soured on this place a long time ago. But remember I need a screwdriver right now and they are walking...

Latest posts

Forum statistics

Threads
45,939
Posts
996,463
Members
39,139
Latest member
meizy
Top