Search results

  1. D

    Seat frame Question.....

    Im not certain but my Burb has a folding armrest on both side of bucket seat, that looks like armrest bracket. EDIT: Never-mind I just saw a picture of my Burbs armrest, its sits much higher on the seat.
  2. D

    Blower motor vent tube

    I would not cover the hole if you use the blower motor alot, may cause the motor to overheat.
  3. D

    Wobbly power steering pump pulley

    My burb had a squeaking power steering pulley with a wobble, turned out the pulley was cracked about a third way around. The crack was hard to see in the engine bay but when I took it off I could see the crack.
  4. D

    1987 Suburban R10 emissions problem due to modified intake

    Sounds like your missing the stock air filter housing and preheat tube. This would not affect emissions out the pipe but it would not pass the visual in California, don't know about CO. In terms of emissions, a tune up will help, BUT do you still have stock intake manifold, tbi, with egr and all...
  5. D

    1991 Suburban 3/4 ton: TBI to Holley Sniper conversion - stupid, or worth it?

    If your trying to build an engine for power sure, but you wont get the reliability of a gm TBI....and I don't see Holley supporting this system in the long hall.
  6. D

    V1500 suspension question

    On my Burb they are 56", they are 3/4 ton springs but some 1/2 tons were optioned with this known as the "heavy half."
  7. D

    V1500 suspension question

    v1500
  8. D

    V1500 suspension question

    Kind of hard to see but here's a picture of my burbs leafs spring. I have 2.5 lift hence the block but if you look at springs I have one fat spring and then 7 more leafs...I have the heavy duty towing package as well
  9. D

    V1500 suspension question

    Rear springs don't seem right, looks like they took out leaf's or put a different leaf spring with less arch. I have 8 or 9 leaf's in my rear spring on my 90 Burb.
  10. D

    Stocking up before 25% tariffs?

    Eh...most of the oversee parts I have bought recently have been crap or needed modifications, looking forward to see some Made in America parts in the future
  11. D

    AC system recommendations

    I followed the write up I found on this forum and just upgraded my system with sanden compressor, dirty dingo bracket, new belt, new style condenser and new hoses. I went this route because I have a suburban with rear ac and the aftermarket kits dont work with my rear ac especially because their...
  12. D

    Vibration

    check your flexplate, any ticking noise, seen cracked flex plates create a vibration
  13. D

    Leaf Spring Torque

    Depends on the size and make up of u bolts, anywhere from 70ftlb to 150ftlbs, I do something in the middle 80-100ftlbs
  14. D

    Electric fuel pump

    Never had much luck with those external electric pumps...I think electric pumps need to be in the tank so the gasoline cools it, that's why oem electric in tank pumps work. Is your fuel return line still connected and free flowing back to tank?
  15. D

    CA Smog exemption

    If that bill passes you would have to buy collector car insurance to not have to smog
  16. D

    Condenser Replaced - a few pics

    You have move all the condenser bushings inward, there extra slots to slot in, top driver side had to drill a hole abolt the original bushing, I also cut some of the rubber bushing in the middle
  17. D

    New from Cali

    Welcome fellow Californian, good luck on your project, hopefully its a diesel vin or you live in a special county, if not you might have to abide by smog laws
  18. D

    UNK sensor

    Looks like the cold start sender for the 6.2 diesel.
  19. D

    Rebuilt Stock Steering Column or Aftermarket?

    Squarebody Synidicate has those shortened Ididit steering columns if you need more room, a bit pricey though
  20. D

    R4 to Sanden whith stock ac lines(for serpantine)

    Not sure, I have a sbc, I would think the only problem may be the lines to the compressor may need to be extended.
  21. D

    R4 to Sanden whith stock ac lines(for serpantine)

    I just want to say thanks to yevgenievich and everyone in this post. I followed his write up on a the r4 to sanden swap and now my 90 burb has ice cold front and rear ac.
  22. D

    700R4 leaking after sitting a while

    I had same issue once I parked my burb on the drive wayy for a while...I believe I had over filled transmission and it leaked through the vent on the top of transmission
  23. D

    Suburban Rear Heat & AC removal/installation/compatability

    Hey Yakko, I'm not a fan of the rear ac fan in burb, I thought about installing a few 120 or 140mm pc fans on the back of rear ac evaporator. May be worth a try for if you can wire it to ac harness
  24. D

    Square-body?

    To be fair what 80s car truck is not a "Squarebody"
  25. D

    Invision Gauges by Autometer

    Seems kind of expensive for just an LCD screen, I rather have some Dakota Digitals that look like the orginals

Latest posts

Forum statistics

Threads
45,582
Posts
986,854
Members
38,672
Latest member
Knightewulf
Top