Search results

  1. 8

    New gauge cluster

    Thanks guys! and honestly i just wanted to try somthing different.
  2. 8

    New gauge cluster

    Done!!!
  3. 8

    New gauge cluster

    Hey guys here is my gauge cluster project I am doing. I am installing sunpro gauges into my gauge cover. Made the holes just a hair bigger. Looks great
  4. 8

    front bumper.

    HEy guys iv got an 86 chevy k20 and i put a 74 frame under due to the original rotted away. Will my 80's bumper fit onto my 74 frame?
  5. 8

    Diesel swap ideas

    Sooo the idea has been going through my head lateyl for a diesel swap in my k20. but i do not want a cummins, everyone does a cummins swap. So what can you guys think of that would be a different but practical diesel swap for my 86k20? Ideas and pics welcome!!
  6. 8

    this is so cool

    This is awesome!! makes me want to yank out my fresh 355 and put this in my k20 https://www.youtube.com/watch?v=0-rSGRU9bzw
  7. 8

    dash lights very dim

    i do have a brand new dimmer switch instlaled. i forgot to mention. I suck at electrical
  8. 8

    dash lights very dim

    where is the cluster ground??/ andyou mean test the wire going from the dimmer switch to the cluster to see if it has 12 volts???
  9. 8

    dash lights very dim

    I replaced all the bulbs in my dash in my 86 with new super bright 194s and i see that they are all working but they are super dim. And yes my switch was turned up all the way lol What can cause they to be so dim?? Like very dim. Im thinkin maybe that printed circut is shot.
  10. 8

    temp gauge not working

    Thank you i will try that! and i have an aftermarket oil gauge so i am not sure but i will check the fuse. The fuel gauge and spedo work l
  11. 8

    factory temp gauge wire color

    Thanks guys, set it up and the gauge donest move after the truck runs for 45 min. hummmmmm
  12. 8

    temp gauge not working

    No the wire didnt strech that far but i had to untape my harness to find the wire that was damaged so installed a new piece of wire, and yes it is screwed into the thermostat housing. I have plugs in the cylinder head where the old one use to be. But i guess i could remove that if i had too...
  13. 8

    printed circut confusion

    Hey guys i have to get a new printed circut for my 86 and on lmc it is asking for if you have gauges or without gauges, i am confused. what does that mean
  14. 8

    temp gauge not working

    I found my dark green wire that is for the factory temp gauge and went and got a new sensor and screwed it into the themastat houseing and let my k20 warm up for about 45 min. The gauge in the truck did not move. hummm. What could cause my gauge not to me working? what should i check.?
  15. 8

    What is the brake pedal Supposed to feel like!?!

    Not really comparing it to anything. I drive a 2013 silverado so i know there would be no comparison. I just know that my pedal is too low, it seems. I can try to bleed it again. And i made a mistake. i am useing the orginal master cylinder. I never had a problem with it.
  16. 8

    What is the brake pedal Supposed to feel like!?!

    great info! i adjusted my rear drums the other day until i felt them start to grab. would this be enough or go more? And again everything is brand new.
  17. 8

    What is the brake pedal Supposed to feel like!?!

    My 86k20 has all new lines and brake pads, shoes, hardware,calipers EVERYTHING! But i did clean out and reuse the proportioning valve, witch is working fine Bled it out and the pedal still feels too low to me. Im not sure how high,hard these trucks are supposed to me. 10.5 axle in back...
  18. 8

    LMC is evil..

    humm lets see. $255 for carpet, $55 for roll of sound deadener/heat insulation for floor, $290 for heater/ac system, and the other day..\ 38-5254 ADAPTOR-DASH VENT ASSY 1 16.95 16.95 In Stock 38-5262 VENT OUTLET-CTR/RH 2 REQ 2 19.95 39.90 In...
  19. 8

    interior color code needed!

    Thank you!!!
  20. 8

    LMC is evil..

    dont get me wrong i have no problem with a good used interior part but..i have spent so much on the rest of my k20 i feel like i should buy new parts . I just the other day on craigslist for $100 got a unpainted pair of door panals with the arm rests, i just bought all my ac/heat vents and all...
  21. 8

    LMC is evil..

    LMC truck can be evil....to my wallet. ha I need to stop buying parts..$200 here $100 here blahhhhh. but on a good note. i have all i need to finish my interior :)
  22. 8

    factory temp gauge wire color

    i have a 86 k20 and the harness is the original too. i want to get rid of the aftermarket sunpro temp gauge and make the factory one work. What is the color wire i should be looking for on my harness that would control that gauge??
  23. 8

    interior color code needed!

    Hey guys, does anyone know what the color code would be for this blue for intieor. I need to give to SEM for them to mix me up a spray can for my door panals.
  24. 8

    how does dash pad bolt/hold in place

    i got a mint dash pad from a pick and pull and i am wondering how it bolts into my dash. It was already pulled when i found it. Pictures would be great. thanks
  25. 8

    Duplicolor interior paint

    Hey guys i bought a pair of GM door panals from a guy of craigslist and they need to be painted. Does anyone know if any of the interior paint duplicolor offers is a match or very close to that blue the 80's the interiors use to be? thanks

Latest posts

Forum statistics

Threads
45,558
Posts
986,231
Members
38,644
Latest member
FenderBanger
Top