Search results
-
Fuel tank
I think the hot setup is to use the return line but no evap canister, and vent the fuel cap. The return line means that gas is always circulating in the fuel lines, so it keeps you from getting vapor lock or boiling fuel in the line by the exhaust. The General didn't just add parts for s**ts...- rich weyand
- Post #5
- Forum: Engine & Performance
-
-
quick easy-ish 350 upgrades
Yup. All determined with a quality wide-band A/FR meter.- rich weyand
- Post #27
- Forum: Engine & Performance
-
quick easy-ish 350 upgrades
Haven't run this setup on a 1405. Edelbrock says they have different venturis, boosters and idle circuit. So my tune may not work on the OPs carb. The factory setup will still be too rich, so he has to lean it out. Bear in mind that I went smaller on both primary jets and rods, so it's not...- rich weyand
- Post #24
- Forum: Engine & Performance
-
What spark plugs make the difference?
Autolite 24. It's what all the mud racers and circle racers around here use in SBCs.- rich weyand
- Post #3
- Forum: Engine & Performance
-
Cam help
Nope. I would probably ask Comp Cams to be sure. Just call their tech dept.- rich weyand
- Post #6
- Forum: Engine & Performance
-
Cam help
Comp Cams simulator says 12-304-4 is the equivalent for computer control. Similar lift, similar duration and separation numbers, similar rpm range, and similar performance. 275hp @ 4000, 410lbft @ 2500. Stock torque converter for rpm range 700-4700 rpm. Probably want to pop the governor off...- rich weyand
- Post #3
- Forum: Engine & Performance
-
Time for an Engine build
Do NOT use the 2601 unless you are also going to use the original thermac air cleaner setup. It will run like absolute crap in the winter (in ND, no less!) unless it has carb heat. The air-gap manifold is great for summer running, because the carb will not overheat, and the intake runners will...- rich weyand
- Post #19
- Forum: Engine & Performance
-
quick easy-ish 350 upgrades
See above in your post: Edelbrock 2701. Unless you want to go with the standard thermac air cleaner like I did. Then you can go with the 2601 air-gap manifold. But you don't want to do that in Omaha without the thermac air cleaner. It will run like crap all winter without carb heat.- rich weyand
- Post #17
- Forum: Engine & Performance
-
Smoking on acceleration
Yup, or warped heads, such as from an overheat. They skinnied up the heads at one point to save weight, and went a little overboard. BTDT, got the new motor.- rich weyand
- Post #6
- Forum: Engine & Performance
-
Weird TDC Question
Look at the top line in this graph: https://en.wikipedia.org/wiki/Piston_motion_equations#Example_graph_of_piston_motion For a pretty wide range of angles, the piston will seem like it is at the top. Top "dead center" means just that, the dead center of the piston curve in this graph. That...- rich weyand
- Post #2
- Forum: Engine & Performance
-
New Guy with "New Guy" questions....
Popping a head and miking the bore and stroke would help a lot. That and the casting number of the engine and the head and it's pretty easy to figure from there.- rich weyand
- Post #14
- Forum: Engine & Performance
-
New Guy with "New Guy" questions....
Also, and I realize I'm something of a heretic on this, there's nothing wrong with the NP203. Just put a part-time kit in it and manual locking hubs. You do need to spin the chain once in a while to put oil in the reservoir above the main output shaft bearing, because, being designed as a...- rich weyand
- Post #10
- Forum: Engine & Performance
-
New Guy with "New Guy" questions....
Even with smogger heads, it's pretty easy to get 300 hp and 450 lbft out of a 383 with the right cam. Comp Cams 12-234-2 looks nice for that. 300 hp @4000, 450 ftlb @2500.- rich weyand
- Post #8
- Forum: Engine & Performance
-
New Guy with "New Guy" questions....
what cam did he put in it? That's the big question.- rich weyand
- Post #2
- Forum: Engine & Performance
-
quick easy-ish 350 upgrades
Or you could tell me what rpm you are running at 60, if you have a tach.- rich weyand
- Post #13
- Forum: Engine & Performance
-
quick easy-ish 350 upgrades
As for gears, do you know what you have? Check the RPO card in the glove box.- rich weyand
- Post #11
- Forum: Engine & Performance
-
quick easy-ish 350 upgrades
OK, several things. With the Hooker headers, they routed the pipe to get a better tune from them, without going full-boat. This makes the #5 and #6 wire routing a little weird. The trick is to use wire holders, and to exit the #5 and #6 wires *first* and loop them forward, then exit the #7...- rich weyand
- Post #10
- Forum: Engine & Performance
-
quick easy-ish 350 upgrades
Yup, that pretty much sums it up. The Edelbrock has its detractors, but it's fine if you tune it. Most people don't, then bitch about it. You can get a good wideband A/FR meter to do it, or I can give you some tuning numbers to try -- jets and rods and springs and such. I'll tell you right...- rich weyand
- Post #2
- Forum: Engine & Performance
-
Cam found but...
I think I would probably do the cam/lifters and see where I'm at. You haven't mentioned that you're having valve float problems now, and that cam and the heads won't allow you to overspeed those stock springs, which were made for higher rpm in an earlier era.- rich weyand
- Post #46
- Forum: Engine & Performance
-
Cam found but...
He's talking about what the spring should test at. It would be on the spring specs, which are often attached with a little tag, or are on the package.- rich weyand
- Post #44
- Forum: Engine & Performance
-
Cam found but...
I guess I can go along with that. It also depends on whether you push the thing up above 4500 rpm. Below that, you are unlikely to float the valves in any case. So, if you drive with some care, you won't stress the valvetrain. Haven't heard yet on what my buddy on the other forum did...- rich weyand
- Post #36
- Forum: Engine & Performance
-
Cam found but...
Also, you need a valve spring tool to change the valve springs. The break-in procedure for the cam is a big deal. The parts have to be pre-lubed with assembly lube. You need to use break-in oil, or oil with break-in additive. Then you need to use oil with ZDDP in it from then on. Here's...- rich weyand
- Post #21
- Forum: Engine & Performance
-
-
Cam found but...
Doing a cam change in the truck is more like $1000-$1200 at $75/hour. It's about a day and a half, and some of it (removing and replacing hood, for example) is a two-man job. Easiest way to do it is to pull the hood, the radiator, the grill, and the hood latch, and leave the engine where it is.- rich weyand
- Post #14
- Forum: Engine & Performance
